Search results

http://www.venturerider.org When you start stripping her down...post at the above forum, always 1st gen owners looking for parts :). Great forum....very similar to this one.

Check out the one Sean is listing on ebay....fly down and drive it home :) I already have one and still keep thinking about it....lol

Thanks Rob (Maxine) :) I always get the jet sizes screwed up. Need to take better notes instead of relying on you all the time...lol. I forgot we put 155's in with the pipes/K&N...assuming we'd need them and then jetted down (back to stock) after getting dyno results. I just knew I jetted...

Maybe wrote it wrong....After I get the nylon screw started threaded, I deliberately pop the spacer out of the detent and roll the needle around until it falls back in. I fully tighten the nylon and then try to rotate to make sure it's still there. I understand your point and see how that...

attached dyno sheet, the one March 2012 was after jetting 1 size down on the main jet, syching carbs, and shimming needles out .019. The other is the initial run...stock VMax, marks 4 into 2, K&N airbox

Dammit...A/F is OK...but lost HP and torque. Time to talk to Mr Morely :) I'll post both dyno sheets when I get them scanned at work.

Evan....agreed about the forum. Absolutely amazing. I've got a friend here in town that is patient enough to walk me through everything the first time and then I'm usually comfortable enough to do on my own. If there was 1 thing to be good at...I suppose carb work would be it, unfortunately...

Thanks for all the help. Took 1 of the 2 shims and put her back together. I did feel one slide sticking/rougher compared to the other 3 so cleaned will a dallop of WD40. Runs like a raped ape now. Wish I knew if it was the excess shim or if the slide was sticky. Side note...getting the...

No dyno sheet...he said A/F was getting up to 17 and didn't want to go any further. He recommended lifting the needles. Have it rescheduled for this coming Tuesday.

Thanks guys...I double checked the retaining part of the nylon immediately after the problem and all the needles are tight. I'll try removing a washer tomorrow and let you know how it goes... I just saw a bunch of posts on here with Marks 4 into 2...and they seemed to be using 2 for .038, so I...

After going to the dyno this morning and finding out I was a little lean in the mid-range...realized I needed to shim the needles. Followed the how-to on here...got the radio shack washer pack, mic'ed at .019. Added 2 washers between the nylon and the retainer clip, making sure to push the...

OK...first off, sorry for the confusion. Definitely came with 152.5's (I blame it completely on my 40+ year old brain :)). Got a set of 150's from Sean and put those in. Seat of the pants seemed crisper, but something about the sound just didn't seem right. Occasional idle issues too...but...

Wow...hard to believe. Thanks guys...I'll keep you updated

Everyone keeps saying 152.5's are stock....but I know I pulled 150's out of mine and pretty positive they'd never been touched.... Specops...I wonder if you just have better airflow than me? weird they'd react so differently with the same pipes. Thanks for the responses....

Bike is a stock '98. K&N filter, Marks 4:2, 2 inch cans, 152.5 jets. Was happy with the 120 ponies....but as you can see, way too rich. Should have left the stock jets (150) in. A friend in town recommended just dropping 1 jet size (back to 150), and make up for any remaining richness with...

Elevation about 700ft Forgot to mention the K&N in a stock air box. I'll see what the dyno says I guess. She runs pretty good...rich if anything but still crisp

Read through a lot of the tuning threads on here, just seeing if this sounds reasonable. 98 V max, stock. Installed the Mark's 4 into 2, shorter cans, 2 inch. My initial jets were 152.5 and upped to 155's, my air screws are all 2.5 turns out. What I've read recommended original jets...

Sorry for the delay... Yes, barely hit, the part you put the foot on to lower centerstand. I could bend I suppose...but do like the look of it without the stand installed. Besides, only 2 bolts to remount...might be easier just to mount it when I need it. Yes, 4 into 2....and still love them...

Thanks for all the how-to's and tips....Mark's exhaust went on easy. Centerstand hits...so that will have to come off in the morning, but otherwise flawless. Sounds amazing....will sleep very happy tonight. Oh....and the throttle response is soooo much better.

A point of contention among HVAC people (kind of like oil type is here :)). My personal opinion is duct cleaning is just a waste of money. Spend the $ instead on getting the ductwork balanced (right CFM to each room), fixing any leaks (found during balancing or with smoke tube), and maybe...