Search results

Hello. I just bought the 'Screaming Banshee' horn for my '98 VMAX. To be honest, having a hell of a time with placement. Anyone suggest a good locattion as to set this beast up? Not worried about wiring but, instructions say to not have it placed where falling rain or wind-forced rain could...

I am still here as well, season is done for me. Bike has been winterized, no mod's to carry out, will be more active in the Spring when I put rubber to the road. Pretty busy with other aspects of my life. Still willing to help a brother out, if I have input. I'm still pretty new.

Still here as well. Riding season over for me, bike put away, no room or money for mod's, other projects on the go.

I installed a 2003 thru 2006 Honda CBR 600/1000 RR Smoke Tail Light with LED Turn Signals from 2wheelproject off eBay. It does require some fabrication and electrical skill attached to it. I did it in an afternoon however, had the tools readily available and moderate amount of skill when it...

Looking to dress up my bike cosmetically, sought guidance from Sean Morley of Morley's Muscle. Was decided to change out stock parts for black chrome. Pretty self-explanitory, find attached the finished product. Looks very sharp (IMO).

We have potholes as well but, avoidable. Sean's busy so he's selling me the parts at a reduced rate and I'll assemble it. Appears pretty simple and straightforward. Sent from my SM-G920W8 using Tapatalk

Thanks. I sent Sean Morley a message. Sent from my SM-G920W8 using Tapatalk

Do you have a recommendation for a taillight in place of reflector? Sent from my SM-G920W8 using Tapatalk

After discussion, and some encouragement from Scott Rollins from the VMAX Forums FB Page, I finally decided to do the CBR taillight Mod. Looks sharp, looks stock and have received numerous compliments. Mod wasn't exactly as per the PDF guide that is floating around. Mind you, I had tools and...

Thanks. When I'd ready to re-assemble, I'm going to print off the forum-notes and take suggestions into account. Here's to hoping that it will work "right out of the box".

Will definitely look into this. Besides, gives me another excuse to purchase another tool for the box....:punk:

Will have to see if I have a compression fitting that will go that deep. May be a bit of an issue. Good suggestion on having them lay flat however, I have been making that a regular practice so in this case, I'd rule that out. Yes, It was mentioned about valves. May be my next step.

Bike did get dumped 3-4 years ago prior to me owning it. Something I will have to try later as carbs are currently in pieces...:)

Sweet looking sync....impressive. Will remember that when I go to re-assemble and fire it up and am ready to sync again.

After dissassembly of the carb's, I checked the tabs...don't appear to be bent. Yes, I can see putting the springs back in to be a PITA....am following shop manual so, only hope I am doing it right.

Yes, found a way to semi-sync while on the bench using two drill bits of same size. Seems to be my best bet as I have the carb's off right now and in pieces. Will have to be something I tinker with later...my job is getting in the way of my fun....not impressed.....however my job is paying for...

Correct. Forward screw sync's #3 & 4 to #1 & 2 however, #3 SHOULD balance/sync both #3 & 4....and it's not. #3 will sync just fine...#4 won't move at all....:(

I suppose it's possible. I've never adjusted the valves. Bike is "new" to me last year. Finding all sorts of things. I've spent a lot of late nights and early mornings getting my bike ready to ride. It spent a good portion of it in the garage last year being worked on. I've put a little...

Good thing to note. I have carb's in complete teardown mode right now. With work commitments, etc,..now looking like it'll be a winter project...sadly it means my riding season is over right now....:(

Tnanks. Think I'll switch at beginning of next riding season as for me, this season is almost over..