My 1988 Vmax build follow along....

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Yes its a curse and a pleasure all at the same time....

Late last night, I wrapped up at 3 am. Still have the rh side scoop to do. Since I couldnt find someone to trade my mint factory black scoops for a set of workable scoops. I stripped them and they are ( 1 ) kromezone powder coat. Looks really shiny, its not chrome, but less maintenance.

11329931_971125876254451_3871274551665542498_n.jpg

Slather on some aircraft stripper....
11351481_971125896254449_1441679119819077898_n.jpg


In minutes a factory mint ( looked like they just came out of the box new ) scoops are being stripped!
11244716_971125916254447_2885129226472630353_n.jpg

Needs a second coat.
10985494_971125932921112_2366065338910486622_n.jpg

RH scoop being stripped.
11053101_971125956254443_2891269001257215248_n.jpg

LH side scoop stripped and awaiting outgassing. Made sure I did it for a long time on this one.
1525066_971125976254441_1727535930332529919_n.jpg

Outgassed.
10985494_971125996254439_5195183871603161028_n.jpg

Fresh layer of Kromezone.
11377282_971126012921104_3987974642084260872_n.jpg

Out of the oven!
11329847_971126029587769_7411465381638880365_n.jpg

On the bike.
11048688_971304999569872_8915022962425935570_n.jpg
 
Yes its a curse and a pleasure all at the same time....

Late last night, I wrapped up at 3 am. Still have the rh side scoop to do. Since I couldnt find someone to trade my mint factory black scoops for a set of workable scoops. I stripped them and they are ( 1 ) kromezone powder coat. Looks really shiny, its not chrome, but less maintenance.

I wish you would of told me, my scoops would have been perfect for you and yours perfect for me! It's looking good though Todd!
 
Yeah...that's the secret for PC'ing cast aluminum (especially engine cases)...outgas them for a loooooonnnngggggg time...couple hours at least...then you're goog-to-go!

The scoops came out real nice...
 
Wow..
Man your work is lookin good. Really movin along too.

Nice Job!!
 
Thanks everyone.

I finished the right handscoop last night and installed one of my brake arms.

Brake arm out of powder coating.
11021088_971885692845136_7270648422593088459_n.jpg


Original arm.

11390301_971885722845133_2803924881997666581_n.jpg


Original and my billet machined arm.
11164180_971885766178462_1651540696545162342_n.jpg


Installed.
11392801_971885799511792_7277729478567924341_n.jpg


Now I have to look at all the bolts on the bike and decide if I replace them or pull them and start coating and chroming them. When I installed the brake arm, the bolts looked like shit and I didnt have time to plate them. So I ll be doing that sometime soon.

Still have to finish the brake coversion. I ve been too tied up to make brackets for the conversion. Simple job I know, just not enough time in the day for me.
 
Its little things like this that take up time.

Had to machine a new nozzle for the media blaster.

11218973_971885312845174_3901053491814717098_n.jpg


I ll make this one last longer by heat treating it.
11393164_971885292845176_1326722113998928293_n.jpg

11021088_971885346178504_1681776232528830540_n.jpg

11147573_971885379511834_8782777991500948113_n.jpg

11377107_971885409511831_8372503891653668903_n.jpg

10425150_971885422845163_1630674445552914015_n.jpg


A little scaley, but its only a media nozzle, I wont clean it, just install and go.
11265080_971885442845161_982181943234324597_n.jpg
 
Thank you!

I just finished my Hayabusa to Vmax Conversion bracket.
Off the machine..
11412267_975053289195043_8004000475501094825_n.jpg


Threading the top caliper mount hole.

11401405_975053305861708_6487981975019701566_n.jpg


Installed on the bike with the busa caliper and R1 rotor.
11401198_975053319195040_6045275893046662546_n.jpg


Hayabusa master cylinder. I am not fond of it and I will switch fo a ZX14 brake and clutch master soon.

11401523_975053335861705_5535389903972470263_n.jpg


11350483_975053352528370_1952925971813962687_n.jpg

One brake was better than two original brakes from the factory. So the next one I ll mount after I get the caliper back together. The master I got was a pile of crap. It was dumped and they neglected to mention it had road rash. And the pictures didnt show it, just the paint being gone.... but oh well for now, the bike has brakes again!
 
Well I had one caliper apart and was going to rebuild both. But decided to ride it a little this weekend with just one caliper. I put 25 miles on it. 15 miles one day to test and 10 miles yesterday to a buddies house and back and then was going to be a few hundred miles saturday/sunday.

But my caliper decided to lock up and ruin a rotor.... I ll post a picture later. So I ended up putting the stock brakes back on and did around 350 miles on them.

Now to get a zx14 brake master and a busa caliper rebuild kit. I might have to get a R1 rotor as well, hoping its just colored and not warped.
 
Back
Top