1300

Well I came to Texas to visit family and pick up a Bultaco Matador that my Aunt gave me. I think my brother about has me talked into taking his old KZ 1300 home. I really do not need another project sitting around but I dont think I can pass it up.lol

I'm looking for information about mod like this. Were anybody put FJR wheel into V Max?

97 Vmav is knocking...time for an upgrade..let me know

http://rochester.craigslist.org/mcy/5680251499.html 2003 FJR with about 7,300 miles on it. Bike runs and rides great. Asking $5,500 or best offer. Located in Rochester NY. Sent from my SM-G920V using Tapatalk

Looking for a VMAX. Have a 2003 FJR 1300 to trade. Bike is located in Rochester NY. In excellent condition. Has only 7,300 miles. Sent from my SM-G920V using Tapatalk

I've been reading and trying to get the A/F mixture screw out of the right rear carb. Can't get it out. My question is this: can I buy a 34mm carb from a 1300 Venture, dusassemble both carbs, swap the jets and replace just one carb?

Bear with me here as this engine is going in to a 1st Generation Venture, not a VMax. My current plans were to take the VMax heads and plop them down on my 1983 Venture, drop in a 2002 transmission and a VMax final drive and call it done. But I have a few "opportunities" pop up recently and...

I supposed both TCI are differents but i cannot find a timng curve for the Venture TCI, if somebody got one....

Soon the riding will be over here so I already am planning one of my winter projects. Building a 1300 for the max. What I have so far is a 1987 venture case with the crank rods and pistons in it. I am going to replace the rods with vmax rods. I have a complete set vmax heads and a transmission...

I just read that today when I saw the picture of the swingarm. Wow, that would have looked great on a vmax. Nice piece, isn't it? Full article is here: http://www.motorcycle-usa.com/273/906/Motorcycle-Article/2003-Yamaha-FJR1300.aspx

Hi would like to know if the stock vmax clutch lever fits with the fjr1300 clutch master or do you need the lever from the fjr

I scored an 86 Venture motor to put into my perfectly happy Vmax. Should I buy heads and cam on eBay and sell off the Vmax motor or pull the parts off the Vmax? Is there any other parts that need to be swapped out that I am missing?

I scored an 86 Venture motor to put into my perfectly happy Vmax. Should I buy heads and cam on eBay and sell off the Vmax motor or pull the parts off the Vmax? Is there any other parts that need to be swapped out that I am missing?

Looking for comments about the FJR vs. the Vmax. Comparisons: Price value, speed, comfort in the saddle on trips, gas mileage, anything else. Never been on one, know nothing about them. What you say?

I have a couple of questions about this build I'm in the middle of, and would appreciate the forums input. This motor is going into a max. 1. can venture rods be used? I know they are the same size as the max but are the max rods better? 2. what should I use for head gaskets? 3. would...

Has anyone tried to fit an FJR 1300 rear wheel to a 1st gen vmax?

Hi, What do you think about my dyno? It's the best result - i remove stage 7 (at stage 7 i has about 97 hp) Vmax '90 engine 2006 venture, venture transmission, vmax cams and heads carb-stock exhaust-supertrapp It was europe ver, now with v-boost. I don't know if cams from europe are diffrerent...

Finaly got her on the dyno at work and did a few pulls and got 128hp and 83tq. I'll try to post graph tomorow. Build is a bored to 1300 10.8-11.1 scr with cleaned up heads done by me, decked 40 thou., and stock cams with stg 7 needles caint remember for jetting lndy filters with stacks and a...

I have always wanted one of these bikes and recently found this 95 on craigslist for 2500 and could not resist. After buying it I noticed the stator cover said "yamaha 1300". Sure enough after finding the engine code, 1NL-000667, and after referring to some threads on this site I now realize...

Hi Folks, I tell you they are is sending my stuff, I must congratulate the state and the order reached by the parties.:eusa_dance::eusa_dance::eusa_dance: Now I'm waiting for the pistons and crankshaft, later reached the upper casing, see the photos, thanks Sean and thanks...