barnett

Hello everyone! I am having some trouble fixing the slipping clutch on my 94 max. I purcahsed it from a guy for $1100 because it had trouble starting and needed "clutch lever adjusted." I fixed the starting issues with carb cleaning and new battery, and figured I would flush the clutch lever...

Just purchased my first VMAX this winter and have been loving it with the exception of a slight clutch slip in the top of 4th and 5th gears. I am planning on replacing with a Barnett clutch pack and full size last friction plate and with a pcw spring. This may be a silly question, but why does...

I've installed the Barnett clutch on my 06 Vmax a few years ago and can't for the life of me recall if the washers provided with the six springs fit easily down the tubs of the purple clutch pressure plate. I'm installing the same kit onto my 2013 Royal Star Venture and the washers seem to not...

Happy to post all these at cost UK or abroad. More, higher-res pics here: http://imgur.com/a/A4To3 Make me an offer on any of the below... Scoops: These have been "de-badged" as the yoofs say nowadays. They've been sprayed black but could do with a respray or a touch up. 40mm...

How hard is it to install a Barnett clutch conversion? I've noticed a bit of slippage in my clutch when I open it up hard, and I want to change out to Barnett pressure plate......now, I've heard some that say they install and can't get clutch to work........some have no problems. I can follow...

So I have been searching the forums and there is a lot of advice/opinions on which clutch option to choose. Basically, I've narrowed it down to these: 1. Barnett Conversion 2. PCW 3. DD I am pretty set on getting the Barnett conversion and the HD springs (90lbs). With that being said, should I...

Clutch was slipping a little so I decided to replace disks. Ordered a Barnett Clutch Spring Conversion Kit and their friction and steel plates. Of course that was before I researched it and saw that that is not the way most folks go. Read this how to post...

can I use 8 full friction plates with the conversion and what parts do I leave out

Fellow Barnett spring pressure plate users, I installed the pressure plate, replaced the fibers and left the 1/2 disk in the rear. Took for a drive an all is good. One thing I did notice was that the clutch engages about 1/2 thru the lever travel...is this normal or am I in for another...

Gday all. It's been a while since I've said hi daily, but work/family/house, you know how it goes. I'm finally getting around to the 2nd gear jump deal, engine will be stripped tommorrow hopefully, getting ready for next season's racing.....in between work/family/house! And yes, back-cuts, etc...

Well I set about re-building the clutch on my '06, (the OEM one was TOAST) so I went with the Barnett spring conversion because I tried the Double D once and it rubbed on the inside of my clear UFO case cover. When I was doing the job and put the Barnett pressure plate on, I noticed it has...

Hi Chaps, I am considering the above and have read the best stuff in here for guidance but would be keen on any thoughts from anyone who has installed this to advise how they found clutch pull after install to the stock set up eg; if it became much stiffer or remained roughly about the same...

Put new clutches in about 4 months ago and went with the barnett clutchesinstead of OEM , and they seemed to slip in 4th and 5th pretty bad under hard loads. Took them all out and skuffed up all the plates and that solved the problem. But I was going to go ahead and do something about the actual...

Need to replace my stock clutch, just looking for a something better.. How is the carbon clutch?? thanks .. nitrous pete..

Anyone else ever have a brand new barnett clutch start slipping in 4th and 5th going about 60..? At cruise and hitting the throttle around 60 the clutch begins to slip along with over revving ofcourse until speed/ rpms level out or what ever, WOT at 100 doesn't do it..... Why would barnett make...

I looked at at the barnett clutch but I don't want purple color. Suggestions for alternative in similar quality are welcome. Vitek

I bought a Barnett clutch kit. (the purple one) The instructions are a single page showing that you removed the old one and bolt in the new one. Is it that easy? I haven't taken a Vmax clutch apart in 10 years and remember none of it.

Well look what I bought to play with - Barnett Carbon Fibre Friction Plate Kit :banana: With instructions that mean bugger all to me :ummm: Does anyone know why there are eight plates in the set :ummm: Where does the little plate go :ummm: I'd appreciate some assistance from anyone who has...

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=260117955343&ssPageName=STRK:MESE:IT&ih=016