break

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. GuyR

    Rear brake microswitch

    Hello As part of my Vmax restoration process I notice that the rear brake microswitch wire is not connected to power supply. Trying to understand where to it should be connected? Any idea please? Can I find diagram somewhere on the net? Thanks in advance Guy
  2. M

    Pulsating rear break

    Last 2-3 months, rear break started pulsating. Break pads are totally gone now. I’ve disassembled the whole wheel for power coating it a while before, but cannot precise if the pulsating started short after that, Any suggestions on how to start looking for the reason as I will change...
  3. D

    Help break into the 10s tricks

    Hey guys, a lot of Knowledge on this page and figured you were the ones to ask. I'm trying to get into the high tens. My current best is 11.27 @114.8 mph. I know my launch needs work but am working on that also. Ok, I have a 07 with ufo headers, slash tip exhaust, Morley muscle jet kit, and air...
  4. Rollie

    Attempted Break In

    I had an attempted break in last night . Someone pried open two downstairs window screens in my man cave . I usually don't feed the pups until the morning.
  5. T

    Engine Break in period

    What is the best method of breaking the new engine in? for the first 200 miles I have been varying the rpm's from 4-9k on acceleration and cruising at around 4k. Not too much red line yet. I knew I wasn't going to get great gas mileage but the fuel light is going on after only 69 miles! I...
  6. CustomMax

    Cut a break

    Last night I took the Max out for a ride and it's running better than ever. So anyway, I was on my way home when after stopping for a light there was a nice usually safe place to give it a little juice. So I started out kinda easy, then I figured it was a good chance to blow out the cobwebs. I...
  7. V4bandit

    Spring Break Prank

    Thought I would share this video, since I laughed my *** off watching it. :rofl_200: https://www.youtube.com/watch?v=1WtdTQP0FLo
  8. medicineman843

    weight break down from stock exhaust

    Coverter 20.8 lbs heat shields 2 lbs left and right muffler 9.2 32 lb weight reduction. if anyone wanted to know how much weight lost. new exhaust is half that. vance hines CS ONE
  9. dinkydau444

    Europe for Spring Break???

    I've seen some postings from people here who live in Europe. I'm trying to think of some Spring Break vacation ideas aside from your typical wild Cancun party. I thought Ireland, Germany, Spain, or Greece would be a blast. If any of you have some suggestions I would sure like to hear them...
  10. V

    Speedometer cable break

    So I'm riding and my speedo stops working and so I think one of the ends is unscrwed, I stop and of course it's the top one, I finger tighten it the best I can and it works all the way home..so I take apart the whole light/screen/brackets etc to get a pliers on it, tighten it up and put...
  11. 2fear

    Rear break squeaking....

    I just put on new EBC pads on the front and rear, my rear breaks squeak / squeal super loud. What the hell is making them do that, and more important how do I make them stop squeaking. I only have about 300 miles on them and it started after about 100 miles....
  12. vmax2extreme

    CHEAP break light flasher

    CHEAP brake light flasher If you like the idea of the Back Off brake light module, then you'll love this one I have found for a fraction of the price: http://www.bigrigchromeshop.com/Merchant2/merchant.mvc?page=BRCS/PROD/LITWH/UP90655 It does the same as the Back Off module and is fully...
  13. kozy

    How to break it off with your employer

    How do you tell a company that you've been working with for a grand total of about 45 days that you're wanting to quit yet still leave yourself an out in case you need to come back? I was offered a highly-desired position with another company in the field that I want to be in, and I'm most...
  14. Thevmaxrider

    Engine break in

    All, As most here know I had my motor rebuilt over the winter by PCW to a 1428cc "stocker" with Sean's jet kit. Well today I decided that after ~1,000 miles (1,400km) to see what it had. Starting from a dead stop I ran it through 1-4th up to 9.5k rpm before upshifting and up to 8.5k rpm in...
  15. Diablotin

    Break disc size (rear + front)

    Hello, I'm planning to make the mod for brake on front and to change the rear disc. I got already the R1 calipers and very nice adapters for those (for 298 mm disc). I was planning to change the front and rear discs, since they are not anymore efficient and they don't look good anymore. I...
  16. 82ndCowboy

    Help! Break Pads not in the same spot?

    I just put on a new set of EBC HH pads today. And I noticed that the new pads come to the very edge of the rotor. The original factory pads only came to about a 1/16 of an inch to the edge of the rotor. Is this something I should be concerned with? I compared the original pads to the new EBC...
  17. 82ndCowboy

    How do I stop brake squeal?

    My front breaks are driving me nuts. They squeel at slow speeds. I've tried keeping them covered, not washing them with soap. And I've used two cans of break cleaner. They are only half way worn. How do I make them stop squeeling?:bang head:
Back
Top