hole

Hello- I would like to know the diameter of the original hole near the needle, the one that is usually enlarged when installing a Dynojet kit Thanks, Henry

'85 Vmax. Why is there water/coolant coming from this hole between the top and middle rib on the cylinder head? I've been flushing the old coolant out with a flush and now just staight distilled water. Second galon flushed through when I saw it bubbling out after a 10 minute idle warm up. Engine...

old owner had supercharged this bike leaving a hole above the carbs so made a plate now got a storage hole just put on some hwy pegs (some old harley ones) for the long trips and sissy bar to stop the misses flying off the back just thought i share it with you all going to set this bike up...

I recently bought V-Max #4 (in my lifetime). Last weekend I discovered some black sealant on the clutch cover just behind the rear brake lever. Apparently the bike had been down before on the right side punching a hole into the clutch cover with the brake lever. The cover itself is discontinued...

A wise guy had drilled a 1 inch hole at the bottom of the stock muffler. Did someone found a simple way to block it? Thank you Eric

Hello all I need your help here! I have a coolant leaking from that hole from that locate on the cylinder. That hole is located inside the middle of the aluminum line (the are three line of aluminum on the head) What is that mean? I got this bike a month ago from USA so I only drive on it...

Can anyone tell me what the stock diameter of the signal hole in the slide is? Drill bit size is fine.

After 30 years of dreaming of a vmax I've finally gotten almost all of the kids out of the house and worn the wife down. I bought a 23k mile bike COMPLETLY torn down in 5 cardboard boxes for 750.00 dollars (!!!!!????) after 2 weeks it's almost done and the only part missing is the rear fender...

Hey Gang, I'm hoping someone can help me. Does anybody know what the size of the holes in the metal inner fender support thingy is? (see red arrow in pic below) (I'm guessing 5/16"..but hard to tell) :ummm: I'm making my own support for the CBR taillight mod, and I do not currently have the...

Bad Post.. Sorry sorry for the double post

Just picked up a '98 VMAX that had a Corbin seat on it. The po just left the seat loose to gas it up. Didn't like that so I saw where folks got a deck fill from a marine supply and 5" of filler hose to extend the filler neck. Thought it would be nice to keep the locking gas cap so I found a...

Hi, So i removed the vboost intake and it had silicone sealant and oil coming out of one of the screw holes. Is this normal? It isn't leaking oil when driving, only noticed it now when i was gonna change my cracked vboost rubbers. Maybe it was the silicone sealant that stopped it from pouring...

Hi, I just installed Morley Jet kit and now it sucks at higher RPMS, I cant even get to 6000 RPM. I did this while i was cleaning my carbs and my new exhaust hasn't arrived yet, so it's still on stock exhaust. The problem is i read CV carb tuning guide and it says if it doesn't pull well my...

Hello, I have been rejetting my carbies and now they are back together I am getting fuel leaking out of the breather on number 3. I think it is caused by the needle and seat. They are clean and I swapped the needle from 3 to 4 and 3 still leaks. Does this mean the seat is screwed? Is there...

I was cleaning my engine block when I came across this pin hole that resides in the dowel hole of the water pump mounting surface. I tried to blow it with air but it seems blocked, I also tried to see where it leads and I could not figure it out. Vmaxers and Vmax gurus any idea? :worthy:

I flushed my coolant the other day and noticed a very small hole at the bottom of the water pump, just under the cover. Being curious I stuck a little screw driver up there to see how deep it is and it just kept going in, but when I pulled it out it was pretty gucky. Anyone know what that...

I dont have a tig welder and not sure if I have the skill to fill the hole without the metal sticking out then needing grinding. Would a dab of JB weld be enough to seal off the air hole? Thanks

Hi all, I have 1986 Vmax. The problem is that the small hole below the spark plug channel is leaking coolent after it warms up. It is on the side of the cylinder head. Does any know where the coolent is coming for and how bad is it to fix. Thank for your help.

Hi all Can anyone tell me the distance between mounting holes centers on a early vmax forks? The pre '90 40mm stanchion ones with double pot calipers. Thanks in advance. PS - I think its 83mm but im not sure

so i have had issues with my fuel sender and took the tank out yesturday only to discover a small hole that looks like its been drilled in the top of my tank. Does anyone know if there should be a hole here or not? second question, when you guys fill your tank do you fill it to the very...