plastic

I am after the left hand plastic cover which hides the cables by the yoke below tank and above air intakes.In UK

Looking for the plastic piece that fits under the fender that the tag frame attaches to. Shipped to Florida

https://www.youtube.com/watch?v=gRCMIDILfEI This video is good and you only need a cheap soldering iron as low wattage is the key. Try it but use a mask as the fumes are very toxic. While doing some work I found my front guard was cracked under the fork brace. Im going to repaint anyway as its...

Hey there, Does anyone know if its possible to get a replacement mesh and the plastic slots for the air intakes? The guy who owned the motorcycle before me epoxied LED's onto the plastic slots and removed the mesh filters on the outside. This seems to restrict the air a little? And a little...

I had a friend misplace the threaded plugs and little springs that hold the needles in the slide. Not sure what happened. Think carbs were apart for a while. I sent him the ones out of my spare diaphragm assemblies. So now I need 4 springs and 4 screw plugs. I can get them I think in a needle...

Hi all, I have a large spot of baked on plastic on a header pipe from a tarp that got scorched. Any tips or experience for removing it? It is baked hard and almost like a ceramic. Amy solvents that might help? Maybe a copper or aluminum scraper? Thanks, Wayne

http://www.krem.com/story/news/local/shoshone-county/2015/03/24/scso-plastic-wrap-pranksters-i90/70367790/ Many years ago when I was at school some idiot classmates had 'fun' tying a thin white cotton thread across the road. It looks like a steel cable in the head light at night...

On the plastic piece that fits on the needle, there is a small little tit that fits into the slide. When you do anything with the needles, you have to rotate the needle, until that nipple falls into place on the slide. Everyso often, i will tend to break the nipple off of the plastic piece...

Plastic shroud in front left scoop that covers the throttle cable linkage box and gets screwed in behind the electrical connections. Need the part number, mine is all broken.

I'm thinking about buying a can of carb dip from NAPA. Never used it before. Will it ruin plastic? The plastic piece that the float drain tubes connect to are still in the body. I also noticed some plastic washers on the throttle shafts under the E-clips. Do these plastic parts need removed...

Anybody have the plastic covers. The one that covers the key ignition. Mine broke today.

Has anybody ever broken the plastic on your fly screen /instrument cowl.https://www.yocracing.com/accessory_store/store/yoc_viewItem.asp?IdProduct=267539

hey what is the best way to remove the neck plastic on either side

I never knew this section was here! I just tripped myself out by finding it! When I pulled apart my carbs I dropped one of the bits of plastic that goes over the choke shaft. The thing shaped like a top hat. I've since cleaned the floor and filtered all the dirt through my fingers, with no...

Looking for comments from experienced members about this type of fabrication. Don't know a thing about it myself but want to learn. Let's say a plastic seat base needed some fabrication, maybe an extension or something. What would you fabricate with and how would you attach to the existing...

I need to paint the plastic trim pieces on my differential and rear wheel. I don't have much experience painting plastic. Saw some Krylon Fusion at the auto parts and see its recommended for plastic. Anyone have experience with this paint? Good/bad?

Hey everyone.. I just put in an order for the black plastic megascoops from exactrep. http://www.exactrep.com/acatalog/info_51.html Now im kicking myself thinking I should have ordered the aluminum ones. I dont want the chrome look I was going to paint them glossy black and metallic red...

I had a badly broken neck cover which seemed impossible to find a new one so I decided to fix the old and the ugly... For those who might be interested in plastic parts fixing I took some photos for the future help. First you need some tools like scissors, soldering iron, tape, plastic putty...

Anyone have an extra i can buy quick or know where to get them?

just found this out this past weekend as my brother's neck cover above the electronics was cracked in half so he just put acetone on the seam, put them together and it holds great, i had no idea. i'm sure its common knowledge but for those of you who don't know...