point

I recently recieved a Ignitech kit. Install was fairly simple. Programming is a bit more difficult. With the kit came a disc with what I assume are programmed set-ups. When I try to upload a set up I get a text (key). Which I don't understand. I'm just trying to get a starting program for...

I've got a craftsman jack I think will work if I put about 4" of support in the circled area. I don't think lifting from the back of the motor will get the front end up so I also need to know if I can also lift from a bit further forward, directly underneath the oil pan.

I really liked his thoughts here regarding failure as opportunities to grow. It starts around the 6:10 mark in the video. Well said with a genuine humbleness. I like this kid. https://www.youtube.com/watch?v=wtH0yUY-wak?t=6m12s

When I drove in this am the clutch was engaging when the lever was barely pulled in. As I got close to work it started engaging closer to full clutch lever pull. Hoping I make it home. Any ideas? Thanks in advance.

Hey everyone. hopefully this is my first post of many on this forum. After owning a half dozen bikes, i have narrowed it down to just having a couple in the stable. i have been looking for a nice gen 1 2006-2008 vmax, but would love to find a gen 2 if the price is right. well i found one...

Edited for content

This ain't good.......... http://www.msn.com/en-us/news/us/radioactive-material-found-in-groundwater-below-nuke-plant/ar-BBpclE0?li=BBnb7Kz

I don't see that much movies but this one I couldn't pass it without sharing in a warning way to all of us. https://www.youtube.com/watch?v=spqZ704Um-s&feature=youtu.be

This is a spinoff of my other thread. I've been shopping pretty hard for a Gen2. I've found '10s listed for as little as $11K and I've seen several low-mile '14s go for around $12K on Ebay. It kind of seems like a no brainer--a '14 for $12K makes better sense than a '10 for $11K, since the...

White Cops Aren't Victimizing Black Youth By Jack Kelly - December 7, 2014 Jermaine Jones, 29, was gunned down in the street on the outskirts of Ferguson, Mo., Oct. 18, a few hours after his sister, Margaree Dixson, 35, had been shot half a mile away. If this is the first you’ve...

House Report: "Choke Point" Targets Legal Businesses for Asphyxiation On May 29, House Oversight and Government Reform Committee Chairman Darrell Issa (R-Calif.) released a staff report, The Department of Justice's "Operation Choke Point": Illegally Choking Off Legitimate Businesses? The report...

I've seen all these threads on replacing the starter clutch, but when it comes to replacing the starter gear there isn't much information. Even the service manual just says to check for wear, but there are no specs on the amount of wear of the boss or the inside bushing. Does the damage have...

I notice that if i have the clutch fully grabbed that it feels the clutch isn't quite disengaging the tranny. I've never had a bike with a hydraulic clutch before and I don't see any adjustment screw. Can someone point me in the right direction? Thanks, Sid

I didn't see an area to introduce myself, so I thought I'd kill two birds with one stone. My name is Bryan and I own and operate MELCENZANAH MOTORSIKLET, in Turkey. I am an American, but moved here a couple years ago to be with my wife and and family. I had a shop in Western NY too for many...

I'm going to jack my bike so both wheels are off the floor, it will be like that and without wheels for a couple weeks. I don't want to leave it on the jack and will use the center stand as 2 resting points and a stack of wooden blocks for the 3rd point. My question is, where to place the...