ring

Does anyone have the link for the guy that makes the VMAX ring with scoops on it I was looking for a nice quality one thank you Dwayne

$40 shipped to cont US.

Is there an alternative to Yamaha OEM for piston rings. Any options more affordable?

i CHECK THIS OUT , ITS VERY HELPFUL WHEN PICKING THE CORRECT TYPE OF "O" RING FOR THE JOB ! :punk: http://www.marcorubber.com/materialguide.htm

Does anybody have a extra speedo drive and the ring that goes in the wheel and runs it? Tx

I lost the snap ring to my clutch master cylinder :damn angry:......can I buy one somewhere? Bike bandit just has the whole kit. Thanks!

Are two of the clutch retainer ring bolts special shear bolts? I just snapped two of them off approaching 70 in./lb and I'm super frustrated. Then I looked at Lvlhead's page and his bolts look totally different. Mine look like factory bolts but were all 10mm. The two that snapped are obviously...

Trying to decide where to go with this. Yammy spec for ring end gap for the stock pistons and rings is 0.0295 total/measured, no stipulation whether it it's 1st, 2nd or oil ring. General consensus from current info is that a n/a hot rod motor needs about 0.004-0.0045 per inch of bore...

Hi, I have just got a couple of head gaskets from a friend, and they seem to be Yamaha ones. They don't have a fire ring built in. :confused2: The parts fische doesn't show a coopers ring, which is the only other set up I have ever seen. Do vmax's have a metal fire ring???

I rode a buddys Vmax and I was surprise at just how easy the thing rode. I was tooling around on my bike the other day and decided to check the ring nuts and head nut for correct torque. I noticed that the head nut was loose so I thought maybe ill check the ring nuts too . I tightened the...

Hi . rebuilding a VMAX and had removed the cable harness. Down to a couple of connections which I want to be sure of proper connection before turning on the ignition. First is the Battery Tender 2 ft Ring Terminal Cable. It has a red and black ring for connection. Where is the proper location to...

Does anyone know if the rear exhaust stopper ring is supposed to be a tight fit on the pipe and hold the pipe in? It is #6 on bikebandits schematic for a 95 Vmax. Mine slips on and off easily and I just installed a new gasket (#5). I tighten the muffler band really tight and I can pull the...

Hey guys, I just made this last night. I took a 24 LED string and tied it into a ring. Then i placed it in my brake light. I figured out the left side of each rear bulb is the power side for when you step on the brakes. I soldered the power wire to the bulb. Then i wedged the ground wire...

I FINALLY DID MY OIL "O" RING FIX LAST WEEKEND , IT WENT PRETTY GOOD ! THE HARDEST PART WAS GETTING THE EXHAUST PIPES OFF ! ALL OF THE GASKETS ( THEY ARE REALLY LIKE SLEEVES ) WHERE FROZEN TO THE PIPES , SO I HAD TO WRAP BLACK TAPE AROUND A PRY BAR & WIGGLE THE PIPES WHILE PRYING ON THEM , THE...

The Max started to whine and vibrate on deceleration so I took it in to the mechanic. He said that I broke the pinion shaft and to get it fixed I need to get the whole package ring and pinion. I don't know any thing about it. Does that sound right to you guys? Mike

Is it possible to see if you have a o ring problem through the oil drain hole if you had a scope. Just wondering ? Instead of dropping the pan. Anybody know ?:confused2: http://www.carbtune.co.uk/c.com/fibrescope.html It doesn't have to be that good, this one is way too much - but it...

I, like many others, would like to put this to rest once and for all. Speculation, hear-say and 21 years of hearing this supposedly problem over and over, it's time to deal with the facts and reality. I'll start out by saying there never was or is an oiling problem, period. I want to be...