spot

Has anybody on here figured out what to do with the blank spot on the center console? It bugs me, and I'd like to put something cool or useful there. Thanks Sent from my SM-G955U using Tapatalk

Hi got hold of some blue spots calipers. Do I really need to upgrade master cylinder.had conflicting advice

So I leave for Newfoundland tomorrow. Here's a link to my SPOT tracker info (I hope). It's a cool device. I'd encourage anyone to pick up one of these things if they're going on a trip of any distance, especially alone...

How many can you spot between the 2 videos? Try playing both at the same time. https://www.youtube.com/watch?v=RZ_dzj_xRe4 https://www.youtube.com/watch?v=AvwUh1A6Jbwhttps://www.youtube.com/watch?v=RZ_dzj_xR

So, needed power for long rides to charge the phone (GPS). Picked up the 12v adapter w/2 USB plugs off eBay for $12. $10 in 18g wire, pack of female adapter, and 15a fuse from radio shack. Drilled a 1 1/4 hole under the ignition switch, put gasket sealer around the whole and used locknut...

My son got a 96 Kawi ZX7R last fall, and one of the things he complained about after riding it was the flat spot in the center of the rear tire. The guy he bought it from only rode it on the highway to work and back, with NO turns whatsoever. I told him he would just have to get use to it and...

I have a 7 inch H4 head light, All other lightning is LED i always protect that Vmax low rate electrical charge system since 22,000Km now at 105,000 i never had to repair any part of it (except battery change) fall on this today it`s near HID without electrical issue just share...

Well, the replacement fuel lines seemed to cure the occasional carb leaking on my '85. Been at least 1000 miles with no problems. Bike starts instantly, and runs strong. Yesterday we were out for a ride, and were on a long stretch of divided highway. Cruising between 70-80 mph. At this...

Question for anyone running one of these calipers on the rear wheel. Do you have a lot of brake pedal travel? With the OEM caliper, I had very little pedal travel and the pedal was pretty firm. I switched over to the R1 caliper and it seems like the pedal is much softer and has a lot of...

Is there a sealing o-ring or anything on the inserts or "spots" on a blue spot or gold spot caliper? I'm looking to get one powder coated but I am not planning on removing the inserts since I don't have the tool. Just curious if there was a seal on the spots that would be harmed in the oven.

Hi all: First: My Max has blue spot calipers front and back, and I'm wondering if removal of the blue inserts will allow me access to the brake pistons (since getting them out from the inside workings of the caliper is a pain in the butt.) Second: I emailed qualitypartsonline.com a couple...

Alright my bike runs OK with the y intake in place, but pulls stronger up to 6000rpms without it, then it stumbles and eventualy pulls thru it till redline. I know the answer is to do a complete kit, and i plan on putting a morley kit in it over the winter (just dont feel like pulling of the...

Hey guys. 1994 Vmax. UFO 4-2 exhaust - Morley Muscle kit installed. Carbs rebuilt professionally 2 years ago, all diaphrams replaced, Carbs synced. At 2700-3200 rpm i am getting a flat sound. kinda like running out of gas but not near as severe and a little bit of popping, kinda like...

hi, my name is jeff. i been a member here for some time, now i need some help! i'm just about to install the new chromed 05 R1 forks on my 97 max. i want to have the calipers chromed as well, but i want to keep the spots gold. i know there was someone who made a tool to remove these. just...

:ummm: I would like to thank everyone for guiding me to this point, but I still need carb help. Have an 07 Max with 2K on the clock. Everything is stock except for the below listed mods. I noticed after I installed the exhaust and air filter that it seemed to be running lean around 4K or so...

I have notcied something but I am not sure it's due to demographics or not, so can someone correct me if I am wrong? Where are all of the Vmax's at? Having grew up in Chicago, and now living in Arizona I've actuall seen Ufo's twice (Key word is "unidentified" and not alien) but never a Vmax on...

I just put on a new set of EBC HH pads today. And I noticed that the new pads come to the very edge of the rotor. The original factory pads only came to about a 1/16 of an inch to the edge of the rotor. Is this something I should be concerned with? I compared the original pads to the new EBC...