stem

IF it can or is their a replacement to shorten that stem a bit ?

BikerDave 99 has a How To Post on pg4 of the How To section of the forum (STEM BEARINGS) I am able to read all of the post just fine however acording to Photo Bucket Im not a $$$ Member thus those really helpful Images next to the instructional post are blocked to me. That sucks I know.... i...

Anyone have luck replacing / reparing the odometer stem as in trip mileage counter stem. Mine is AWOL so Ive taped around to keep water out. Positive note...the odometer still works fine.

Will the ram mount fork stem base work on a vmax? I see what looks to be just a cap over the hole but it it is going to take some effort to remove. Want to be sure before I remove it and probably break the cap

I am wanting to relocate my front signal lights on my 95 in order to put a sport shied on it.I have had a hard time finding brackets for it.I finally found some but i need to know the diameter of the stem in order to order the correct one.Anyone know the diameter of hole that I need for a bracket?

Hello I have found lots of info on replacing and setting up the bearings here. But not any list of parts used. Not sure what comes in the packages. I have these Yamaha part #'s for an 1989. 93332-00001-00 and 93332-00008-00 Is this all I need to order? Am I missing anything else? After...

Hi all: I hope everyone's doing okay out there. Question for y'all about installing some new 90 degree valve stems I purchased for my Max. They are from Moto-D Racing, and can be seen at this address...

What side is the valve stem on a stock setup? I assume the front is on the right side (sitting on the bike) as most are due to sidestand lean but on the rear there is more room on the pumpkin side, so i'm just curious which side yamaha put it on? thanks!

Can anyone tell me the diameter of a stock Vmax steering stem at the point where it goes through the upper triple tree? Or the diameter hole in the upper triple tree. My bike is an 1985. Thanks

my question 2004 vmax bought brand spanking new, about 70 000 km or about 55 000 miles, just ripped off the heads, striped them when removing the intake valves noticed that the upperside of the valve, ON THE STEM SIDE, there was a build up ( dark black pretty shure an oil build up ) guessing...

Hello, Let me start off by thanking everyone on here for sharing their knowledge with people like me. :clapping: I don't post much but I'm on here all the time looking for answers and what I can do do my bike. I can't even count how many times I was stuck and got my questions answered by doing...

Hi guys I need to know the measures of the stock steering stem and the thing is i cannot disassemble mine (i have no bench/jack/stand where i have the bike right now). Is there anyone that have a triple set around that can tell me those measures? Thank you in advance Fred

I dont have my valves here in front of me and I need to order a valve guide pilot to cut my valve seats I think they are 5.5mm? or if any one happens to have a guide that they could lend out for a neway cutter with a .375 top. thanks

hey all. gonna have to put a valve stem on the new rim once its done at the coater. i have some aftermarket stems and i attached a pic. in a test put-on today, the problem is i can barely get the second lock-nut on. i removed the original rubber nub closest to the outside-side and...

Hey all. I have started to an odd puff of oil smoke on start up So i am assuming that my valve guide stem seals might be leaking. - though it was a bit odd, two cylinders appeared to have oil fouled plugs, then i took it for a 20 mile ride and checked after and no wet oil look on any plugs -...

Anyone know the size/threads of this offhand?

Anyone have or have seen the valve cover caps that light up while the rim rotates? I think ALL HD guys hould invest in a set so we have a light show at night to ooh and awww over.

Here is a picture with the machining dimensions required to make an Ultima Inverted Harley type front end fit the Max. The stem supplied with the front end needs to be re machined as follows in the pic.