syncing

So.. I had an issue with the carb sync. It mainly had to do with the vacuum on Cylinder #4. I'm having an issue that the sync just won't line up. I pulled the carbs to clean but found they were basically spotless on the inside, I still ended up rebuilding the #4 carb just because I was in...

I just purchased my first vmax last weekend . It's a 06 with a stage 7 and supertrapp exhaust . It seems to have a hard time at idle and I was reading you need an experienced mechanic to sync your carbs with a stage 7 kit . I live in the suburbs of Chicago and would like to know is there any...

Where I left off, the "shotgun" fixed my bad idle/ low power question. Today I decided to try to sync the carbs and to futz with the air-fuel screws. 1) Even if I tightened the screw for carbs 3&4 all the way, they still wouldn't go to the same vacuum. Thoughts? 2) Tightening the air-fuel...

Ok, I was syncing the carbs, it stalled out. I tried to start it again and now shes dead. Here is what's working, Headlight, running lights turn signals, horn, front and rear brake lights Here is the dead list, Starter, fan, neutral light, Fuel pump. All fuses are good. I checked them...

Good morning. After going through the forums I've found a lot of useful information however didn't feel any of the threads answered my question. First off, this is what I have and repairs I've performed. Own a stock 1998 1200cc VMAX. No mod's have been done to this bike. Maintenance I've...

Quik question. I feel the carbs need to be synced on the 95 I just bought. Would anyone know why I couldn't use the "old fashioned" vacuum gauges instead of the Merc or Protune? Thanks:ummm:

Hello All, Looking for a step by step on syncing my 2000 Max carbs. I have the tools, I think, just need the how. Thanks Jeff:ummm:

Hi everyone just wondering if anyone knows why i cant seem to get my left and right sides synced together. I had them synced fine but then ran out of gas and sucked some junk into my carbs so i had to take em off and clean them again, other than cleaning the only change i made was moving my...

I know I saw a how to guide for syncing carbs but I can't find it no matter what I search, has it been removed? It was a sticky so I'm sure it is still around but I can't find it.. If anyone runs across it can you please post the link Thanks Ron

Looking at getting a carb sync tool and was still just a hair unclear on the readings. I read the tutorial and it says to tune 1 and 2 then 3 and 4 and finally left to right. Sounds simple enough but I still have one or two small questions. Using a gauge I will be looking at numbers. Are...

Is there a way to sync my carbs with a single port vacume gauge? I know it will be a pain to go from carb to carb but is this possible. also what is the easyest way to adjust the 3 adjustment screws for the carbs? Thanks...

Has anyone used this tool for syncing VMAX carbs and, if so, how effective is it? Thanks. http://www.jcwhitney.com/autoparts/Product/Pr-p_Product.CATENTRY_ID:2008076/c-10101/Nty-1/p-2008076/Ntx-mode+matchallpartial/N-10101/tf-Browse/s-10101/Ntk-AllTextSearchGroup?Ntt=carb+sync+tool#CommunityTabs

I've had the MAX for a few months and it already need to be synced again? It's an 05 with a little over 7K miles on it, it had about 5.5K when I bought it (I've been out of the state all summer :( ) and needed to be synced pretty bad. RAN MUCH better after sync!! Now a little over 1K and it's...

I started to sync the carbs this morning and I got 1 & 2 synchronized, and 3 & 4 synchronized, but I ran out of play on the L - R sync adjustment. Any Ideas? Would a sticky V-boost cause this? I do hear the servo actuating when I turn the bike on. Brad