advice

So I need some advice here... Basically went to install my new galfer wavy rotor last night (something that SHOULD be easy) and ran into a whole fuckload of problems.... I got the rotor off easy enough, but noticed one bolt was a little tough, didn't think much of it. Once i got everything...

Hi all, I got my carbs and seat and chrome parts back from Sean today ( Thank you very much Sean !!!! ) So this afternoon and tonight I plan to install my carbs and sync them. I did make a rookie mistake when I took them apart and didn't note which cable was in which linkage hole :bang...

So my Carrozzeria rotor bolts, are rusting. :( They sent me a new set of them to "coat" to prevent this from happening again. So, how should I stop them from rusting? will powdercoat chip when I torque them down? Will chrome on just the heads work? Thanks in advance for the...

Does anyone know how to remove the air/fuel screws after they have been damaged? The A/F screw heads on 2 of my carbs are damaged due to being ripped out by trying to turn corroded in screws. They were flathead, but now look like the safety screws used in bathroom stall dividers, aaand the...

Ok, heres the short story: I got the bike out yesterday for a bath and decided after a pre-season check and test ride around town, to take my kid for a ride and get some dinner. We took a nice loop out thru carroll to go to Kingys and the bike ran great right up until it died about 10 miles...

I need help. I've spent all morning researching all the posts and stickies and just get more and more confused. I've seen about three different methods of measuring float settings, and a slew of different numbers. I'm confused how a setting of 1.125 equivocates to 15, 16, 17mm's since...

For whatever reason my water pump started leaking from the weep hole. So I replaced the complete assembly with a new one from Bikebandit,com. Here's the issue I get everything put back together, start her up and while checking for leaks I see theat my oil is contaminated (milky):bang head:, I...

So lately my girlfriend has been working alot of evening shifts, and for the past couple months has been carpooling with a male co-worker. At first I didn't mind, I would rather have someone with her in case she has car trouble or something like that, but it seems that they have become a little...

I just finished testing the 4 coils I got from Pinwall and 3 coils Morley sent. I also just tested a set of p/u coils from Morley. I'll post the results of everything: My '85 (on the bike) pickup coils: B-O: 119.9 ohms B-W/R: 120.4 ohms B-Gray: 121.6 ohms B-Whi/Green: 120.5 ohms Morley's...

What's the general price range for this? I'm assuming tires will be $100-200 each? Besides new wheels what else would need to be done/bought? You can't just buy different size wheels and stick them on, right?

Won the recent auction for 2001 VMax ignition coils from Pinwall Cycle Parts. I don't recall seeing or reading about any damage. They showed up today and 3 of the 4 have cracks along the underside. Seems like eBay has changed so that the seller of the part can't leave negative feedback for a...

I am planning on buying a 150CC scooter due to the gas prices. I drive 60 miles round trip to work 4 days a week in my Maxima that gets 22 MPG and my VMAX is just a lil better. I spend about 65.00 a week in gas. So I am planning on buying a 150 CC scooter to drive back and forth to work, and...

Hi all. Just picked up a set of Supertrapps for my '05. Got the stockers off without much difficulty. However, I'm yanking my hair out trying to slip on the Trapps. On the right side of the bike, I can match the ends of both pipes but it appears that the alignment of the pipes is off. On the...

OK guys, I made my mind up, I ordered the UFO Dragstar exhaust today for my 07 Max. I'll do the V-Boost disconnect too, or should I go with the T-Boost on/off setup? Also, I'm thinking to just go with a Stage 1 Jet Kit for now. I'm looking for a improved power gain plus mean sound. Later I'll...

I am 6 ft @ 195 lbs. and am considering a set of progressive 412 shocks. My question is: 1.Do I need to alter the side and center stand to for the 11.5 inch shocks? 2. What do you experienced gurus say as to shock size? 11.5 or 12.5 or even 13"? Thanks again for all of your support. I don't...

OK men (and gals), I'd like to pose a scenario to you to help me decide on a VMax purchase. A friend of mine has a 99 Vmax for sale. Here's the goods on it: 28,000 Km's 17 inch rear wheel mod- (Radials in great shape) Supertrapp exhaust front fork mod done ISO grips passenger backrest TBoost...

Hi guys, I wanted to know where should I install the ballast ? It's not a slim one. I tried the air scope, but it looks impossible. Since I have a small headlight cowl, I just put it for the meantime behind the speedometer. But I would prefer to hide it, to avoid anybody to get a free ballast...

hey folks I'm about to tear into my '90 model forks to add racetech emulators and springs. my first question is about spacer length for preload. now, I'm used to modern forks with preload adjustment, so this is a one shot deal unless you want to add washers or shorten the spacers? I...

Anyone know cheapest way to send stuff overseas (30-50lbs) USPS? DHL or something else?

Hello All I am stoopid I am swapping my pumpkin with one from a 93 venture and failed to notice before I tore everything apart that the venture's pumpkin does not have a mount for my shock :bang head: Now that I have everything apart I have some options and I am hoping you guys might lead me...