assembly

Hello. And thanks for all the pointers on the fork spring install and all that info that goes with getting it done. I do however have an issue that I have not found in any search. 2003 Max. 15k, allegedly absolutely everything is stock. When it comes to the oil seal area. Basically...

..Just removed my rear wheel from a 1999 vmax.. I am trying to figure out the proper way to re assemble... ..There was a washer inside the diff stuck in place - but i dont think it goes there - as a washer was missing between the frame and brake caliper bracket.. ( looking at the grease marks...

I took my forks apart on my 95 and need to double check to see if I am putting them back right. I have a small spring, about 1" long and same dia as the main spring. now does this go on the dampiner rod before i put it into the tube? The parts that came out are leg, slider tube, small spring...

Hey, New here and I joined because I just purchased and 86 vmax.:eusa_dance: But I have a very odd carb question. The bike ran great but after a while, it started to backfire when I let off of the throtle so I figured it was ready for a rebuild on the carb since I was not sure of what the...

This is a pic of the drain cock valve assembly. There have been different posts on where the on/off positions are located. When changing coolant this valve is turned to the "ON" position to properly drain all the coolant, and to the "OFF" position after coolant change is completed. The...

I'm finally putting the forks back together. Do I replace piece #24 with the washers Race Tech supplies or does the upper RT washer stack on top of this piece?

Found this on ebay today and thought that I would pass it along. It looks pretty much the same thing as the ones a guy was selling on ebay under the vmax section for $150.00 ++ The side bracket is a bolt on style and can easily be taken off so that the taillight and license bracket can be...

Anyone have have the early model pick up coil assembly (2 pick ups) that they want to sell. This is for an 88 VMax. I can't remember what year they went to the single unit. Any ways looking for used as I don't feel like shelling out $400 to the dealer (and it's back ordered anyways!).

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=140264733963&ssPageName=ADME:X:AAQ:MOTORS:1123 I want to find the headlight assembly pictured on this ebay seller's vmax. Any information would be greatly appreciated. Thanks in advance.

Does anyone else think that the tail assembly (tail lights, turn signals, license plate) looks a little cluttered? To me it's the only eye sore on the bike, and it'll probably be the first modification I make. Thoughts?

I just got my 07 and I love it. What a sweet ride. The only problem is that they were sloppy with the assembly. My right mirror (Brake side) nut is all fubared not to mention that they slipped with the wrench and gauged up the hydraulic res. next to the mirror nut. What way do you loosen the...

Hello all.. I have an 86 vmax that I tore down due to a knock.. I just got the cases split and pulled the drive axle assembly out.. The First BIG Gear on the end - seems to have alot of play on the shaft... IS this Normal?.. I dont see any scoring or wear on the shaft itself and the bronze...

Has anyone ever changed the drain cock assembly (DCA) if so was it difficult, mine is leaking from the on-off nut when the engine is cold and the temps is below 10 degres. I would imagine its from the contraction and any worn o rings in the assembly Does the DCA simply pull out of the...

Looking for a fairly new (not worn/torn) seat assembly for my '85 Max. I had my seat redone by Jon at UFO (Starfighter). It is very comfortable on the tailbone, but it sits a little low and the arm/handlebar/seat/foot relationship isn't right for me. Has only been used (ridden 6-8 times) in the...