front

Hello Friends, I have been rebuilding my forks on my 1986 this week and upon removing the wheel I saw that the bearings are not sealed but open rollers. They seem to be fine, but I thought since I had the wheel off I would replace. Should I go back with the open rollers or replace with...

Local chap is selling a 99 st1100 front end complete. Brakes, clamps etc, is 815 long from top to axle.

Master cylinder is from a 2006 Kawasaki EX500. Flawless condition with adjustable short lever. Works great with a single 6 piston caliper setup. Asking $50 shipped to conus. Use [email protected] to contact.

How "should" my front brake feel at the lever? I have new braided lines to install but it feels pretty weak. I have to give it a lot of pull to get anything out of it. I'm not use to this feeling and I'm using the rear quite often. Coming off my 06 cr 250 which will stand up on the front...

So the brake light comes on with the rear pedal. I have power to the front brake revoir micro switch. I also have power to the Y where the front and rear brakes meet. The factory crimp was in bad shape so I re soldered and it looks good. I get power from the front brake switch all the way...

Hi guys, looking for some feedback from those who have USD forks. I'd like to know IF there is much improvement from OEM forks with racetech emulators vrs upside down jobbies. I've been loooking at m50 Suzuki forks, but my suspension guy says they have a basic fixed cartridge, reckons sorted...

So now that I got my carb issues squared away I want to get everything dialed in. I have a leaking fork seal so I'm going to replace both of them so I want to lay out my current setup and get some opinions on what oil and PSI I should be running. I'm 6' 3" 210lbs and I'm not trying to carve...

Currently running a 14mm master. Looking to put stock 5/8 back on. The 14 was nice with the 320 rotor/6 pot caliper conversion but it's a tad bit spongy with dual brake setup.

Does anyone know of a paint that closely matches the gold center of '98 front rotors? Nothing I've seen in the local hardware or box stores is even close. TIA

Can you run a gen 1 Vmax without a front fender and more importantly, the brace that holds it? Or is it necessary to stop some wheel wobble? I am trying to put a bigger tire on the front and was wondering. thanks CvS

I picked up some 6 pot FZR1000 Sumitomo Calipers. I will be changing to galfer steel braided lines. Which are better, going with original 3 line with splitter or 2 line? Which will be easier to bleed? Also, are HH pads the best for these calipers? Thanks, Don

4 front fenders all need painting $ 40 each plus paypal fees & shipping. Please email instead of PM [email protected]

Rumored to be a replacement for the Brembos on the Ducati Panigale. The wheel is also a prototype and has been awarded the coveted "more-organic than carbon-fiber" award by a leading environmental group.

I am looking to widen my front tire to match my 240 rear tire. Any suggestions would be appreciated.

Brakes worked fine before removal, no issues. I was running a single stainless braided line to the right caliper with a shorter line looped over the fender. The looped line will be included but not the line from mc to right caliper. Asking $130 + shipping.

It bolts up directly to a 97 fork. It's rough looking, been sitting for years. No pads. Make an offer + shipping.

i found a small crack in my 03 front rim is there any places that sell factory rims or anyone in the US have one laying around they can let go

My right front cylinder is running much more hotter than the others. Spark plug in right front shows lean clean burn, the other 3 show very rich. Switch the plugs, no difference. Turned the A/F screws in on the rich cylinders, will not lean out. If the situation was reversed I would be...

Hello all, I finally had time this evening to give my '85 a good wash and make it ready for the riding season. After talking to her nicely, she finally fired up. Things didn't sound quite right and after feeling all of the headers, I found the front left didn't want to put blisters on...

Any idea where I can find those pesky front fork caps that screw onto a schrader valve? 1997 Vmax.