line

Hi. Could someone tell me whatrpm the VMax 1200 red lines at please?

Hey guys, Ive been off for a bit. kind of against my will. I went down on my 95 and have been laid up recouping from the hard drop. I busted my back up (it was broken in a car wreck years ago) this didnt help me much. I am getting better and will be doing a rebuild on the bike for certain. Im...

Im looking to replace my brake and clutch lines with ss line's does anyone know of a full kit for a good price. I want good banjo's and clear coating on them. Also can i get ss speedo throttle cable.

1936 Chevrolet Assembly Line This is really awesome footage. A 1936 Chevrolet assembly factory. Note the automation that was already in place, the workers lack of any and all modern safety equipment, glasses and helmets, and they ALL know exactly what to do and its getting done. Note also...

So last year I upgraded my lines to SS. The slack in the clutch line and in the line from the master brake cylinder to the splitter wasn't too disconcerting back then, but now the slack is annoyingly unsightly. So I'm thinking of shortening them. Don't worry I'll leave some play, but right...

SALINE MICHIGAN 6th annual front line youth center ride SATURDAY 9-17=11 SALINE MICHIGAN: 601 woodland drive saline michigan 48176. Hosted by U.A.W Local 892. Ride leaves at 10am sharp. Have tanks full. It go's 110 mile's two parks and 2 pub's food and refreshments along the way. IT end's at...

I bought a Russell clutch line and it is made to go directly to the slave cylinder. I want it to connect at the rigid pipe like the stock one does. Does anyone know what type/size fitting I need to put on the line I have. I'm hoping someone local can cut off the banjo fitting that is on the line...

I replaced my front brake lines with Russells and also bought a Russell clutch line. It looks to me like there is no way in hell it will work. It is several inches too short to go directly to the slave cylinder and there is no way it will hook to the hard line. has anyone used one of these...

Does anyone know the correct brake line lenght for the rear brake line if you are mounting Busa brake on the rear? The stock one I ordered (braided) looks to be at least 4" short. Ok, second question. Has anyone here mounted a Busa brake on the rear yet? I thought I read a thread somewheres on...

Every time I think I have everything fixed something else pops up. All of a sudden both my front brake lines are leaking above the banjo bolts. Are there any cheaper options than replacing them with the expensive stock ones? This is on my '93 Vmax. After I get this problem and my oil leak...

I have a cable in my possession that runs from the positive terminal of the battery to the alternator in a car. It is the perfect length to reach from the battery to the starter on the vmax. I want to replace my entire lead possibly improving my cranking current. I have done everything on my...

Long-time lurker, first-time poster... I began installation on my '88 of a Russell clutch line yesterday. No instructions included or available on their website. However, it appears to me, based on the angle of the fittings and the length of the line, that you need to retain the stock hard...

My carbs require the flue line to be routed down low between the cylinders close to where the oil breather is. This creates a high spot where air gets trapped in my fuel system. Iv removed the air before but its a pain in the ass preventing fuel from spraying all over uncontrolled. Can anyone...

was doing a burn out today on my 85 max (yeahhhh not 2 good for the bike i know but they look good lol) and after i had finished there was oil all over the place over my engine top to bottom. on first thought i thought i had blown a gasket, thankfully not tho. it all came from the line from my...

I want to switch to SS lines and found this to be the best offer on ebay... http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=110635579345&ssPageName=ADME:X:RTQ:MOTORS:1123 Those guys however dont know the lenghts/fitting/angles of the vmax hoses and want me to supply them :ummm...

When the weather gets bad and there's nothing to do, you can help watch the southern border, day or night, if you want. I just started watching again, off and on. Haven't seen anything recently but I have seen a bunch in the past, dope runners, human traffickers. It's a zoo down there. Mexico is...

Quick question. In the process of swapping out my Vmax diff for a Venture diff. The Venture diff I bought came with the drive line still in place. Do I need to swap the drive line from the Vmax to the Venture diff? I measured them both and it looks like the Venture line is a 1/4" longer. I'm not...

Went to bleed / flush the clutch master the other night and had an odd experience. Opening the bleeder without touchingthe clutch lever resulted in a continuous flow of fluid, to the extent that my master reservoir was draining itself. I don't know if I have a residual pressure issue that...

I'm going through my 94, updating everything I can. The bike's running as perfect as it ever has for me. I'm trying to head off the next Gremlin that'll try to ruin my riding fun. I want to replace all of the Gas / fuel lines / hoses with the best stuff I can find. Something that'll hold up...

I was just wondering if anyone had some pictures of the 2 line setup. I am trying to figure out a good routing. Also, does the double banjo bolt from the divider thingy fit the master cylinder? thanks Greg