removal

Am I missing something? The manual and picture show the slave coming right out of the cover. My slave doesn't agree. I have the VooDoo exhaust and the pipes are preventing it from dropping out of the bottom. Which way does it come out?

Has anyone removed their reflectors on the sides of the radiator? Are they just on there with sticky tape? Thanks Jim

So I shamefully laid the bike down the other day. Only thing that got hurt was my pride, engine bars, and my shift lever. I don't have the tools to bend it back into place so I ordered another. Thought I'd start early and remove the bent one and found out it's never that easy. Lo and *******...

Hello ppl. Vmaxer from Denmark here. (so i hope you understand the text) Im about to change my stock rear light to a Led light, and i ran into a problem. I cant remove the tail light since the wires are so damm short. So i have a few questions. 1) Do i need to remove the inner metal...

Hello chaps, I'm going to be removing my vboost system in order to fit my supercharger (that's the plan anyway). Am I right in thinking that the whole vboost set-up consists of the controller, the motor/solenoid and the set of intakes with the butterfly valves? Or is there more to it...

I have a dump bucket sitting under my kegerator taps in the garage. The wife pulled her vehicle up to far so the bucket flipped over so that a ring of old beer awesomeness is stained into the garage floor. I have tried WD-40 and carb cleaner and nada. Any other ideas? Power washer maybe...

My speedo needle snapped off. Is there a way to remove the glass so that I can glue on a replacement? The center hub part is still there.

I need to know what size wrench I would need for the flywheel. I know the nut is 19mm, but what of the hex portion of the flywheel? It's definitely bigger than 27mm. And the channel locks I got just do not provide the needed leverage or grip.

Has anyone done it...is it possible ? I was thinking of getting all brackets in the carbies yellow zinc plated and dont want to not plate the pivot parts attached to them. Any thoughts ??

Bought a beautiful fork brace, problem is I have to remove the front tire to install it. I don't have a center stand so I'm looking for suggestions on how to remove my front tire? I've tried a lift style jack but with my exhaust system I can't jack on the frame and Im not crazy about lifting on...

I haven't taken things apart to see what I have but guy I got my 90 model from said they did 1280 kit, stage 7 and removed vboost butterfly. I hear vboost cycle when ignition turned on but no "boost" feel. Does this hurt my performance? Should I fix it? The cyl has a scratches mark in it, he...

Is there any way you can support the gen 2 if you need to remove the front wheel, without special tools?

So, I want to remove my center stand and while I can easily see the two bolt which hold it on getting access to them is a different story altogether. Any tips? Seems like the mufflers is blocking it on both sides.

OK guys. Many of you may have seen the '85 I'm parting out in the Parts section. It has a nice Kerker on it that I'm switching to my '94 which has a "not as nice" Kerker. My question is, does anybody have a neat trick for separating the two halves without dinging the chrome or, worse, denting...

Morning! I am replacing the left crankcase cover gasket and the old one is pretty crusted on. Just wondering if y'all have any tips for removing it completely. Scrape it off with a sharp knife?

So 3 years ago I had an entrapped ulnar nerv... It destroyed my left hand. The clutch on my bike isa little too tight. I will not be racing like Todd... I remember something being said about removing Springs. What all is evolved and which Springs. Thanks y'all

Recently obtained the Morley HD Oiling kit. Must remove exhaust system to install. Assume everybody knows this. Went to right side of bike and put the proper socket on the big nut that screws into the nut behind the flange on top of the megaphone right behind the passenger peg mount. Hard to...

Ok, I have discovered a pretty big problem with my '94. :real mad: Last year it developed a small oil leak at the bottom of the Crankcase Cover 2 or Secondary Gear Cover. Thought to myself: no problem, I'll just replace the gasket. Much to my horror when I pulled the cover off the lobe for...

uh...noob here. I have a new battery but the charging rate almost non existent. Multi meter shows this. I looked for the voltage regulator "behind the left rear passenger peg. It's there, I see three white wires and one red wire and they go up to where somebody cut out the connector and...

Removal of the Vmax engine in 20 simple steps! *Note - many of the steps listed can be done in alternate order. **I also may have missed some minor stuff and will update this as needed. ***Eventually I will put pictures with each of the steps 1.) Put Bike on Centerstand, ATV Lift, or Alternate...