remove

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    How do I remove the rear fender?

    I removed the two main bolts, and then unscrewed the metal piece under the fender. I don't know how to get the fender off with the wiring going through it. I tried taking the tail light apart, but the wires off of the housing.
  2. misiek93

    How can I remove the steering stem?

    Hello, Let me start off by thanking everyone on here for sharing their knowledge with people like me. :clapping: I don't post much but I'm on here all the time looking for answers and what I can do do my bike. I can't even count how many times I was stuck and got my questions answered by doing...
  3. SpecOps13

    Remove Before Flight Flags... I've Got Aerospace...

    Hatter worked on this for some time. He sent the 2 larger flags and I came up with a means to hold them in my Mark's Exhaust System... Way Cool on his part... Big Thank You..... The Smaller flag fits the Kerker 4-1 on my 89.... Got it from GE Aviation Division....
  4. ninjaneer

    Releasing the Inner Beast

    This started out as a simple re-badging project. I had found some Decepticon badges and thought about using them to dress up the out-dated intake manifold covers, but they were too big. After much deliberation, I finally settled on replacing the Vmax emblems on side covers with them. I...
  5. ninjaneer

    How To: V-Boost Intake Manifold Assembly Remove/Install

    As part of my crankcase breather housing job, I had to remove the carburetors and V-Boost intake manifold assembly (VIMA). I found what I needed as far as removing the carb rack on the forum, but as far as I could tell, the forum lacked a How-To for removing the VIMA. So here goes: First...
  6. Lew L

    How to remove an item in the for sale section

    How do I remove and item that I listed in the for sale section of the forum??? Lew
  7. alorio1

    How to remove clutch push rod guide

    Can someone tell me how to remove clutch push rod guide. I am replacing the seal and thought I would replace the guide also. Thanks in advance for any info on this matter.
  8. S

    How to remove emblem on side cover.

    How do I remove the Vmax emblem on the side covers? Mine are really scratched up so I want to polish them.
  9. D

    how to remove rear wheel bearings

    I have a 1990 vmax. Need to replace rear wheel bearings. Has anybody tried driving old bearings out with a socket? What has worked for you? Thanks:ummm:
  10. bikedave99

    How To Remove Swingarm & Swap Differential

    Alright, so now I have the wheel, shocks and stock mufflers off. It is not necessary for all of this to be off in order to pull the swingarm but it is was done as I was working on other items. Next I will be pulling the swingarm so that I can replace the bearings and swap on a Venture...
  11. rebar

    How do I remove this fitting to add oil?

    Here's a pic. It looks like its four parts. Blue Nipple threaded into the oil cap. Blue nut on that. Thin blue nut. And then the red nut. I tried to hold the thin blue nut and loosen the red. It started to turn but wanted to turn the braided hose.:damn angry: What's the correct way to...
  12. G

    Remove exhaust, old or new gasket?

    My Kerker 4/1 pipe is looking dingy. Thinking about removing it, prep and paint with engine paint (500 degrees). When I put it back on should I use the old gasket or get a new one? If I have to take the old gasket off is there any special way of doing that to make it easy or does it just...
  13. bikedave99

    How to Remove Stock Mufflers

    So, after I pulled my rear wheel and all of the associated hardware, it was time to pull the stock mufflers off. Keep in mind that you do not have to remove the wheel to do this, I just had it off because the next step was swingarm removal. Oh, and most of the visible moisture is water as I...
  14. bikedave99

    How to Remove the Rear Wheel

    This will be part of a mini series on removing the rear wheel, exhaust and swingarm, replacing some bearings, swapping on a Venture diff, and changing the tire. First up is just pulling the rear wheel. Ok, put it on the centerstand, and brace the front if possible: Next, pull the cotter...
  15. V

    How to remove the old exhaust

    Hi. Sorry for asking this silly question ; can someone point me in the right direction when it comes to removing the old mufflers to replace it with a supertrapp slip-on. I cannot seem to figure out which bolts I need to remove to be able to rempove the original. :ummm: Should be very simple but...
  16. EAGLEPI

    To remove the rotors or not??????

    I'm torn between taking the rotors off the wheels and risking stripping the bolts or leaving them on and risk the place mounting my new tires damaging them. I have never used this place but it seems that everytime I use a place to do work on my bikes more times than not they screw something...
  17. wheeliepup

    How to remove glass lens from speedometer

    I have called upon this forum to correct a minor problem with my speedometer fogging over on the inside. I did get several responses but none of them offered a remedy to this problem without risking the possibility of damaging the glass or the bezel or ruining the cosmetics! These speedometers...
  18. gamorg02

    remove swingarm bearings for powdercoat?

    if i'm going to powdercoat my swingarm, can i just pop the bearings out and leave the races in and just buy some new oil seals and pop the bearings back in when done with the seals? or is it a good idea to remove races and buy all new bearings. i wanna do it right but if its not gonna affect...
  19. B

    How do you remove the wheel bearings?

    I'm just starting the project to replace front/rear tires, brake rotors and pads on my newly acquired '95 Max, and decided to replace the wheel bearings and grease seals while everything was apart. It has 45,000 miles on it and has been rode hard and put away wet lots of times. I've done a...
  20. Geek_Law

    How to remove front wheel and brake rotor

    Re: Geek_Law's V-Max Transformation Ok, somebody was asking about the front wheel. I think it was ghostintheshell, but others have asked me before how hard it is to remove a wheel. Well, I had never done it on the max, but it took about 5 minutes. I took pictures to document the process for the...
Back
Top