screws

I am rebuilding my transmission this week. I have the engine broken down and found that the t40 screws (4 ea) holding the middle gear bearing are stripped. I need to ID the size for this screw. Also found the 3 screws holding the main axle bearing stripped as well. I need to ID the size for...

Have enough of these left over to do 4 bikes. 100 was the min. purchase. Installed on my bike and sent 1 set out already. If you like black, here they are FREE. And they engage all the threads on the carb, unlike the ones I removed. Just PM your address and I'll send them.

Finally getting around to changing over to the higher output stator, (thanks CaptainKyle). The side cover came off no problem despite having to juggle the gears that wanted to come along for the ride. The ******* screws put up a hell of a fight :bang head: due to their being installed with the...

Does anyone have a good source for the clutch and brake master cylinder cover screws? Mine are all chewed up and I need to replace them before I have to easy-out them. Surely there are some stainless ones out there...?

Okay guys here's a tough question. My fuel screws are seized in carbs 1 & 2. The cylinders only fire when I blow through the fuel vent hose which forces fuel into the idle circuit. I adjusted 1&2 carbs vacuum to pull harder, hence pulling more fuel. Now all cylinders are firing but I can't seem...

Where the heck is the procedure for setting the A/F screw positions? I know that a dyno or an A/F meter is the best way, however I thought I recall a procedure to get you close for those without access to these resources. Since waking the bike up after it's long winter nap I have had a...

anyone know how to get these bad boys completely out ??????

Hi folks: Question re. reattaching the pickup units that mount around the stator: The screws that Yamaha uses to attach these pickup units appear to be crappy soft metal (SO soft that I broke one of those screws while backing it out from the crankcase cover!) So, my question is this: Is...

Hello, Does anybody know how to set the idle mixture screws? I did the "shotgun," and synchronized the carbs with the carbtune, but I'm not 100% sure I got the mixture screws back to where they were originally. I'm also, not sure they were set right to begin with. I put in "sea foam,"...

I'm not 100 % positive but it just seems like my 2002 Vmax is running rich at idle and low RPM. I know from past experience they all seem to smell rich at idle but this one is over the top to me. My question is whether it would be worth it to drill out the plugs and attempt to change the mixture...

Hey guys, I was wondering if you could tell me the OEM Yamaha part number on the screws that hold the intake manifold covers on? I need to sync my carbs and two of the scews are on so tight I am going to ruin them to get them off and I'd like to have some new ones on hand. Thanks fellas

Hi Everyone, The bike was idling like crap so I wanted to tune-up/clean the carbs. The holes for idle mixture screws were open so the caps must have been removed by the shop that the original owner had Stage 1 Jet Kit installed. I bought plastic plugs and covered them up but I guess it was too...

Does anyone know the part# for this Screw , washer set up. I noticed mine are missing so Choke lever floats and can not set choke without holding. Just bought the 88 Vmax 1200 and have started to replace missing parts and screws as I discover them.

well i guess i screwed the pooch..... I was going to do the shotgun cleaning on my carbs and all the mixture screws are frozen. with much PB Blaster and much more force I got 2 of the screws loose. But the other two screws started to chip. The edges of the slot in the screw head is...

First of I usually use the mid grade gasoline, with the idle screws pretty much all set at or around 5 turns out. Over the weekend not paying attention I had put in high grade gas. Going in stop and go traffic I started having a really hard time taking off and keeping the bike idling, it was...

Does anyone know what size stainless steel screw that is used on the stock carbs side covers? I lost one of mine and just realized it when I was tightening things up. Thanks in advance!

I picked up these neglected V Max carbs on C/List. They have been sitting a long time so I am in the process of disassembling everything, dipping everything in Berryman's, replacing buggered parts and hopefully make them whole once again. I was reviewing other threads and I see the PO replaced...

Hi, I`ve been busy setting up my Vmax. After syncing the carbs, it was time for the pilot screws. I set them at a preset value of 2.5 turns out and started the bike and drove it around until it was warm. Then I started to find the setting at which the engine runs the highest RPM at idle, which...

I've read and printed out the how to to sync my carbs but it's a bit confusing. On the right side there are 2 screws left and right or front and back and then on the left side there is another screw. can someone tell me so that I am clear about what each screw does. I assume the right and...

So I drilled out my brass plugs and instead of a screw it looks like I have a brass plug with a hole in the center of it. I know I didin't hit the screw with the drill bit because I was able to pull the plug out almost intack. Anyone seen this?