slave

1986 Vmax rebuild: >Cleaned the cylinder bore with some 400 grit to try and get rid of wear/rubbing marks.. Assembled with a new K&L kit.. The piston is a little notchy when you move it in and out... Maybe I can use a dremel with a polish wheel to smooth it out?.. Was afraid to wet sand the...

Hey trying to remove the secondary gear cover. I think that's whats its called. Iv tapped with a rubber hammer for quite some time. Any tricks for getting it off? No I havent removed the generator cover yet.

Hi guys, wondering if anyone can shed some light on this. Just finishing cleaning up clutch slave and was checking the new washer i got that fits on the housing part num 90430-10171-00. Now i recheck it is the correct number but it is ever slightly larger od then the old one and doesn't quite...

i removed and dissassembled my slave cyl. on my 86 to clean it out really well and was wondering if i needed to lube the seals with any type of grease or oil before i put it back together.thanks

I've replaced all the frictions in my bike with new ones (including swapping the half disk for a full one) and did the DD mod while I was at it. I've also replaced slave cylinder with a brand new one. Changed all the hydro fluid as well. I'm still experiencing a real HARD and QUICK slip at...

my 2003 has a small leak that I cant seem to find the source of.The drip will show up just where the chrome heat shield ends on left side(as you sit on bike)Doesnt seem to leak at all if you let it sit and idle only shows up after a ride. Am i right in thinking maybe this is the source of my...

I have the worst luck. I pulled the slave out of my 86, it had a rip in the seal. No big deal, I have an 85 project I can rob one out of.... I pulled the middle gear cover only to find this torx type broken star piece. It looks like it was sheared off/broken. It was floating in the small...

which parts do I need to get to rebuild my slave cylinder on my 86 with O.E.M. parts?,or is the slave cyl. rebuild kit @ Python a good reliable purchase.Thanks..Dave

I have a new in box Slave Cy, left over after I sold the bike, if anyone is interested please let me know. I paid $70 I think so just send me an offer and I will cover shipping. Thanks

I'm thinking the clutch slave cylinder is bad on my 1991 Vmax. I found some fluid under the bike and the fluid in the clutch resevoir is low. The bike is also shifting a little harder tha usual. I'm planning on buying a new complete slave cylinder instead of rebuilding my current one. I'm...

I have a new clutch slave cylinder and new clutch pipe and fittings. I'm still finding hydraulic fluid on the garage floor. What's the deal with that? Anybody have any ideas?

I just finished replacing the tranny on an 85 vmax, which resolved the second gear problem, but I have an oil leak coming from the base of the clutch slave unit. I pulled it, found I had installed it without the larger oil seal over the clutch piston. Put it back together and the leak is even...

I have had a new Slave Cylinder to put on the bike, but my question is about removing the old and installing the new one. Do I have to remove the crank case cover and the other cover that is behind the peg to get to the slave. I have looked under the bike and can't see how it would be done...

I think I might need a new slave cylinder but am not sure if its that or if my tranny is taking a crap. I have a 05 max thats stock and only has 5600 miles on it. First of all the bike tries to jump ahead when starting it warm or cold. Then it shifts hard slightly grinding into second and...

Folks, Does the flat side of the crankcase seal face the slave cylinder or the other way around? I did mine a while ago and I don't remember. I have a friend of mine with an '88 whose rebuilding it and for the life of me I can't remember. I sure as hell am not going to tear into mine to find...

I've got the FJR master installed, and have been attempting to bleed for the last 2 days with no good results. It doesn't seem to engage the clutch until almost near stop.