tool

Question I want to bounce off you guys. I have the Motion Pro Sync Tool and the fluid in one of the chambers is low on fluid. I know they make the refill fluid, but no one around here has it. It's like $5-6 online and then shipping is over $6. Not that $6 will make or break someone, but I...

stumbled on this race removal tool and was curious if anyone has used it, thinking 20 bucks might be worth a try, i already did the races on my max but my other bikes need them done soon so i figure it might be worth a try...

Which one is most recommended the motion pro? or the carb tune? i just need to order something that is gonna work and not be a major pain in the rudy.

this thing really worked today ! it looks like **** (not painted very well) but the dam thing worked real good ! the carbs were way out, now it runns like a ***** ape !

I have a 2010 VMAX and want to change the frame badges (silver triangles on the sides just to the rear of the engine). Does anybody know which tool is used to remove the 3 bolts/screws? It appears to be a Torx but I want to be sure. The Torx bits I already have are too small. I have a history of...

For anyone looking to use the newer GSXR or Busa forks to put USD on you bike there are all kinds of costs you probably won't think about. One that I just found out about is that you need some "special tool" to remove/install the axle on these bikes. All it does is go in the end of the axle to...

when I did my '89 vmax I had to purchase a special tool, a socket to disassemble it for powder coating, does anyone need one of these?? would like to sell it, used twice cost me almost $100 and is only available to yamaha dealers

the stock rear axle nut, steering stem nut, and swingarm bolts are all 27mm. for $15 this thing has been used so many times. i love it and finally found a listing for it so I wanted to share: http://www.harborfreight.com/hand-tools/wrenches/27mm-combination-ratcheting-wrench.html

the 17mm (for drain plugs) x 27mm (for rear axle, triple nut and swingarm nuts) would be cool to have for touring, altho a bit expensive: http://www.bikebandit.com/msr-rider-wrench?WT.mc_id=2194329

Does anybody have the tool to grip that funky nut thingy on the dampening rod ?? I am trying to change my fork seals , and after watching the video that Sean made, The damn seals are glued in or something `cause I can`t get them to pop out and the alan bolt in the bottom just keeps spinning...

Hi folks: I'm having a VERY hard time finding a "Damper Rod Holder" tool (Yamaha part # YM-01445) for the forks of a 1994 Yamaha YZF750R. These forks are USD, and very dis-similar to the Max's...but they are USD, so who's complaining? Well, I AM in this case! The problem is that Yamaha no...

Wonderful tool! Airport Scan

Check out this new tool I got - a digital scale. I originally wanted to weigh my floats, but I haven't had a float scale in years & the new digi-stuff is way more accurate & easier to come by as well. I got this scale with free shipping all the way from Hong Kong to Palm Harlem for only 10 bucks...

What is the general consensus on the factory tool kit. Do you carry it or leave it out? I weighed my tool kit and it was 2 lbs. :ummm:

hi, my name is jeff. i been a member here for some time, now i need some help! i'm just about to install the new chromed 05 R1 forks on my 97 max. i want to have the calipers chromed as well, but i want to keep the spots gold. i know there was someone who made a tool to remove these. just...

Hey guys, I picked up a set of used 440 progressives this week and the lower caps have been ground down on one side. I called progressive and their going to give me a couple of caps free. ( very nice service from Beth over there) The problem is it requires a tool to compress the spring in...

what kind of machines do you guys work with, the only machine tool maker left in the the usa is haas, which are junk, 5 years at the most, every machine we have got in the last 5 years, i have had to update, add new controls and program, it's sad, the usa was at one time the largest machine...

Has anyone used this tool for syncing VMAX carbs and, if so, how effective is it? Thanks. http://www.jcwhitney.com/autoparts/Product/Pr-p_Product.CATENTRY_ID:2008076/c-10101/Nty-1/p-2008076/Ntx-mode+matchallpartial/N-10101/tf-Browse/s-10101/Ntk-AllTextSearchGroup?Ntt=carb+sync+tool#CommunityTabs

Dont know where to post this so i decided to make a new topic. Kill me if that was somewhere else :ban00000::biglaugh: I've found it some time ago: http://woodsware.aciwebs.com/gears.asp

So I'm shopping around, looking at the various carb tune tools available, most of them at a pretty high cost, and having some HVAC experience, it occurs to me... Is there any reason I can't just grab a few $10 vacuum gauges off the shelf at my local HVAC supply, 6mm tubing atc, and make my own...