wheel

I just had my tires replaced with ME880s front and 170/80 back. I had then recieved a call from the shop who switched the tires. They had called because they found a spacer from someones rim. Maybe mine! I put every thing I had taken off by me back on in the same order. Could someone please post...

Hi all...does any have the drive side of the rear wheel drawn out? I need the measurements for the cush drive holes and the interior dimensions for the bearings. Thanks in advance.

I am thinking of sending my 85 rear wheel too Kosman too have it cut apart and made into a 18" wheel. I was just wondering if anyone has done this too a 85 rear wheel and if they are happy with the workmanship also I would like too see some pictures of the completed wheel any advice on this...

I need to get my wheels powdercoated, however I have been advised by the company doing the work to remove the six rubber drive dampers - cush drive rubbers from the rear wheel as the wheel needs to be heated to 230 degrees in an oven to bake the coating. I have tried knocking them out with a...

Has anyone used or seen anyone use a 21" front wheel? Pros and cons? Thanks.

Hi guys just finished the wider rear wheel. Now it goes for powdercoating

Guys Need a bit of your attention and insight. Can anyone with a stock rear wheel tell me the diameter of the "spokes section"? I mean the diameter of the disc that connects the hub to the outer ribs of the rim where the air valve is, in other words twice the distance from wheel center to the...

Anyone know the dimensions of this? Don't want to pull the wheel to find out.

Has anyone tried to fit an FJR 1300 rear wheel to a 1st gen vmax?

We are rebuilding a 1990 vmax and have some questions about the rear wheel. For parts 2 and 3, i have them pressed together, but when you put them into the wheel there's nothing holding them from falling into the wheel itself? And also, is the bearing, number 6, suppose to sit on the lip of...

anyone know the reason that the rear wheel is offset??

Ok guys I am looking for a front wheel chock to put in the back of my truck. I am heading to get my bike from Sean in Kansas and would like a wheel chock. My last truck I hauled my bike with the front tire against the front of the bed and ruined my bed and the back of the cab. So I am looking...

Do the the newer vmax's have 17s fitted or no, or if yes, will they fit or if no what others (if any) would fit

Hello everyone, I was looking at switching out my stock 15" rear for a Kosman 17". Any thoughts? Thanks, Rob

So, I had a little problem on the highway. Bent both rims, but kept the Max upright. Now I've got the wheels straightened but a little "nothchy" on the rear wheel when assembled. I wanna change-out the rear wheel bearings but not seeing how the drive-side bearing is removed. Anybody done...

Hello, Does anybody know if a xj900 rear wheel fit on my vmax And is there any modification needed. If modification needed who nows what to do. regards Marc:ummm:

anyone tried this combo? I'm thinking since the XJ900 Diversion is a Yamaha shaftie.. Not sure how wide it is though, but the original tire size on the bike is 150/70-17.. Edit: Just found the wheel width, it's 4" wide.. just a bit too narrow for a reasonable swap I guess.. Edit 2: Perhaps a...

Hi Guys, I got a new back tire today, when I got home (which was an hour drive from the bike shop) the guy from the bike shop phoned me to tell me he just found a bush from my back wheel which they accidently forgot to put in. He is coming to pick up my bike the day after tomorrow (which I...

Just thought I'd share how I got the rear bearings out. I'll skip over how I got the first set of bearings out as you get those out the same way you get the ones out of the front wheel (less than 5 minutes for that). I first destroyed the cage and removes the needle bearings leaving just the...

I think someone asked before but is there any other source for the hub covers that Cozad used to sell besides Exactrep?