wire

What would be the best way to clean my wire harness? It's grimy from all the years and I want it to look like new before I reinstall it. I have no idea what would be a safe way to do this. Soap and water? I don't want to just tape and wire loom over the dirt. Thanks again for the input.

Hey guys, I want to change out the stock wire that runs from the stator to my R1 regulator but, I can`t find any monster wire above 10 Ga. It is way better wire than primary automotive wire but I`m a little worried about the current flow to the regulator may be too low because of the thickness...

i ordered a set of taylor wires with strobe caps on e-Bay before i became a member of this forum and realized that cops would be the better way to go, so rather then having them go to waste i would like to use them, the e-Bay ad can be found here...

I am going to upgrade my plug wires...has anyone used the Taylor Pro 8mm wires, and how the hell do you get them in the coil? Thanks, Chris

ive got a set of 8 mm plug wires another deal on e bay they fit in the plug end fine then i tried the coil push shove grunt cramp wd 40 them more twist wiggle 2 1/2 hours later no new wire seller says will fit have sold hundreds all customers happy all but me i wasn,t drinking or smoking or...

Where would be the closest place for me to tap into a 12V power source near the speedometer? I'm installing a KOSO RX-2n on a 85 VMax and don't want to run a wire all the way to the battery for power. Thanks.

Well i was syncing my carbs at dusk and noticed the sparkplug boots(where they attach to the sparkplug) on my #3 and #4 cylinders were randomly arcing against the head! damn:ummm:, that might explain some tuning issues im having, so whats the best route to go? i figure i might as well get all...

I am going to be making a small run of these COP's harness kits. They will made of all new connetors:eusa_dance: ( not used or scavaged ones from a wrecking yards) . They will also have a high temp sleeve over the wires. At this time I do not have a price yet , due to the fact that the...

Ive read many "this is what i like to use for plug wires posts" but can anyone tell "what should be used" i have to assume the wires that are on it are originals(1988) and the last vmax i had i remember using yellow accel wires with ngk plug caps,but ill be damned if i can remember which. i...

Has anyone here ever had to go around fireblocks in a wall to run wires? I'm planning to run all my wiring for the surround sound system in the living room and the TV is on an exterior wall and I really don't want to have to cut the wall open to do this. Can I run the wires up through the wall...

I am having trouble deciding how to update my plug wiring. I need to be confident I can take long trips without being stranded and just haven't been able to get there after reading every post on COPs. No one seems to have taken a long trip yet (I have taken 3 trips of 3500 miles in 7 days each...

....I am considering running the hot wire from the R/R directly to the battery with an inline fuse....but I am not sure what size fuse would be correct to protect the unit? Anyone that has done this care to say what they used?:ummm: -Mike

Where can I buy NGK spark plug wire caps in North America?

I need a little help i am putting my cousins 06' back together after replacing the bent frame and i got to around the rear coil area where all the wires meet and don't know exactly where they run they just seem to be in the wrong place to me. plus there are some single wires with bullet type...

I want to add some color to my spark plug wires. As they are kinda new don't want to replace and have heard a suggestion on covering them with colored heat shrink tubing. What size tubing should i get and also any thoughts on the subject? thanks Michael hansen

Does anybody have an extra one of these? My pops needs one as one of his plug wires keeps slipping out of the coil. Thanks!

If I pull my wires off the coils and noticed some green corrosion, can I simply trim the wire and reinstall? Is it that simple?:ummm:

I'm looking to make a simple switch where I can stop the servo in place. I want it so I can stop it during it's cycling to keep it wide open, then switch it back when I want it to perform normally. I searched and can't seem to find which wire is the power wire for the servo. I did find the 3...

I need help with my V-Max wire harness. I replaced the old one and now need help hooking the new one up. I will be using a R-1 Regulator and my issue are only with the conections coming off the harness by the regulator. Please contact me on or off list, If you provide an e-mail address I will...

Hi All....I?m trying to get all the things clear to start rebuilding my engine...and I note that i don?t have this part... What is the function of this part? Could someone please take a close photo and some measurement of it so I can build one...? Thanks very much!