Help Support VMAX Forum:
PM sent
nswizard
Well-Known Member
Hi guys,
I did another shotgun cleaning and this time used bit more air pressure and now all 4 cylinders start
Engine works bit rough and I noticed few things:
1. cylinder that did not work has lower temperature then other 3
2. I've took out air filter housing and checked how membrane parts move. On problematic cylinder there is 50% less movement when I rev the engine compared with other 3.
3. Here is the video that shows vacuum values at the moment. First gauge is connected to rear left (problematic) cylinder, second to front left, third to rear right and fourth to front right.
https://www.dropbox.com/s/bze4pwn0v7b8dbw/2016-09-13 16.33.52.mp4?dl=0
4. While engine was running I tried to change position of idle mixture screw in problematic cylinder and there was no change at all, even if I screw it all the way in or turn it out 3-4 turns.
5. There are no more bangs from exhaust.
Did not check valves but will check over the weekend.
He is alive but needs a red bull?
Vlada
I did another shotgun cleaning and this time used bit more air pressure and now all 4 cylinders start
Engine works bit rough and I noticed few things:
1. cylinder that did not work has lower temperature then other 3
2. I've took out air filter housing and checked how membrane parts move. On problematic cylinder there is 50% less movement when I rev the engine compared with other 3.
3. Here is the video that shows vacuum values at the moment. First gauge is connected to rear left (problematic) cylinder, second to front left, third to rear right and fourth to front right.
https://www.dropbox.com/s/bze4pwn0v7b8dbw/2016-09-13 16.33.52.mp4?dl=0
4. While engine was running I tried to change position of idle mixture screw in problematic cylinder and there was no change at all, even if I screw it all the way in or turn it out 3-4 turns.
5. There are no more bangs from exhaust.
Did not check valves but will check over the weekend.
He is alive but needs a red bull?
Vlada
blaxmax
Well-Known Member
Your red bull is on the way and almost there.Should be any day now.Hi guys,
I did another shotgun cleaning and this time used bit more air pressure and now all 4 cylinders start
Engine works bit rough and I noticed few things:
1. cylinder that did not work has lower temperature then other 3
2. I've took out air filter housing and checked how membrane parts move. On problematic cylinder there is 50% less movement when I rev the engine compared with other 3.
3. Here is the video that shows vacuum values at the moment. First gauge is connected to rear left (problematic) cylinder, second to front left, third to rear right and fourth to front right.
https://www.dropbox.com/s/bze4pwn0v7b8dbw/2016-09-13 16.33.52.mp4?dl=0
4. While engine was running I tried to change position of idle mixture screw in problematic cylinder and there was no change at all, even if I screw it all the way in or turn it out 3-4 turns.
5. There are no more bangs from exhaust.
Did not check valves but will check over the weekend.
He is alive but needs a red bull?
Vlada
nswizard
Well-Known Member
Synced all 4 carbs and engine work nicely now.
So it seems that only stubborn dirt in carbs was the problem.
Uhh finally. Thank you guys for all the help and ideas.
Can you tell me what is the procedure now?
Clean plugs and let engine run on idle for 10-20 minutes and check how plugs look like?
Then clean them again and ride for like 50km and check plugs again?
Vlada
So it seems that only stubborn dirt in carbs was the problem.
Uhh finally. Thank you guys for all the help and ideas.
Can you tell me what is the procedure now?
Clean plugs and let engine run on idle for 10-20 minutes and check how plugs look like?
Then clean them again and ride for like 50km and check plugs again?
Vlada
blaxmax
Well-Known Member
Synced all 4 carbs and engine work nicely now.
So it seems that only stubborn dirt in carbs was the problem.
Uhh finally. Thank you guys for all the help and ideas.
Can you tell me what is the procedure now?
Clean plugs and let engine run on idle for 10-20 minutes and check how plugs look like?
Then clean them again and ride for like 50km and check plugs again?
Vlada
You were asking me for this----Go ahead and install the cops too.
nswizard
Well-Known Member
Just to add that I've installed COPs and vmax became a rocket.
Thank you Blaxmax.
Vlada
Thank you Blaxmax.
Vlada
