Carbs help

[Jamie182861]

I need help how set float values any videos or guides

 

[Fire-medic]

Some things to check.

 

[Jamie182861]

Thanks it kept flooding my bike came I believe it float value what is right specs for them

 

[Fire-medic]

The 'bench-set' with the casting mark circle on the carburetor body, is a starting-point. Do a wet-set using the service manual directions for best results and fuel economy (specification is on the last attachment, above).

VMX12- Service-Manual.pdf (vmoa.net)

 

[Jamie182861]

Thanks appreciate ur time and help

 

[RadiumPHX]

The 'bench-set' with the casting mark circle on the carburetor body, is a starting-point. Do a wet-set using the service manual directions for best results and fuel economy (specification is on the last attachment, above).

VMX12- Service-Manual.pdf (vmoa.net)

I am curious where the wet set (15-17mm) is measured from (starting point)?

 

[Jamie182861]

Booked them into a mechanic

 

[sdt354]

I am curious where the wet set (15-17mm) is measured from (starting point)?

There is a line cast on the sides of each carb. If that's what you meant?

 

[dannymax]

The thin white mark on the side of the cone.

 

[RadiumPHX]

The thin white mark on the side of the cone.

View attachment 80044

Thank you

 

[Fire-medic]

From the manual pp. 208-209 of 405 pp in the .pdf VMX12- Service-Manual.pdf (vmoa.net)





The '#5 piston valve center line, in the factory manual, is what dannymax is referring to as the "thin white mark on the side of the cone."

Letter a in the service manual is the fuel height in the clear plastic tube.

You can use a piece of clear plastic tube and make two marks, 17 mm apart. Line one up with the carburetor casting horizontal mark dannymax referenced, and the meniscus (the fluid level in the tube) should meet the other line, when the carb float level is correct. Bend the carb float tang which is attached to the carb float needle up or down to change the level of gasoline in the bowl, to match the desired level.

 

[RadiumPHX]

From the manual pp. 208-209 of 405 pp in the .pdf VMX12- Service-Manual.pdf (vmoa.net)

View attachment 80045

View attachment 80046

The '#5 piston valve center line, in the factory manual, is what dannymax is referring to as the "thin white mark on the side of the cone."

Letter a in the service manual is the fuel height in the clear plastic tube.

You can use a piece of clear plastic tube and make two marks, 17 mm apart. Line one up with the carburetor casting horizontal mark dannymax referenced, and the meniscus (the fluid level in the tube) should meet the other line, when the carb float level is correct. Bend the carb float tang which is attached to the carb float needle up or down to change the level of gasoline in the bowl, to match the desired level.

Thank you very much, crystal clear now

 

[user 16790]

so to do that wet set method you need to keep removing and replacing the carbs from the bike ?, that could take a lot of times if the amount needed to be adjusted isn't quite right each time,
is it not possible to put fuel in the carbs and measure while they are off the bike fixed to a level surface, surely the floats still float and closes the needle,
it would be easier to make sure the carbs are perfectly level when off the bike as the bike itself could be leaning a bit in any direction depending on ground surface and stand wear or even if the carbs sit straight in their inlets, or doesn't not being level matter ?

 

[wayne billings]

That sounds reasonable to me J. Tomkins

 

[MaxMidnight]

it would be easier to make sure the carbs are perfectly level when off the bike ...

I think to 'on bike' process would be for checking; should adjustment be required then you would do that off bike and re-check while they are still off.