rear wheel hub help please

[likembikem]

I am having problems seeing how the rubber mounted rear wheel hub comes off. I am stripping the wheels to have them powder coated. I thought the hub just pulled straight up off the 5 rubber cylinders in the wheel.:ummm: The service manual just shows pictures and I am still not sure. Also while I am at it, what all do I need to do to fully strip the wheel. How do I get the rubber cylinder inserts out? should they be replaced with new ones. Thanks, I want to get this done soon, weather is too nice. My tires are worn out and I want to get this done at the same time I put tires on.

 

[one2dmax]

You don't need to take the rubber dampeners out (they are a bitch to do anyway). They will survive the coating process/heat. To get the splined drive off there is just the one external snap ring.

 

[fmcandrew]

To prove Sean's point here is my stock rear wheel that I PC'd...

The rubber is high grade and survived the long temp ramp-up and 400 degree cure with only very slight impact.

 

[wildweasel_pt]

You can see the groove for the circlip on top of the needle bearing housing

 

[likembikem]

Snap ring....I am going out to the garage to take care of that right now, thanks a lot!

 

[likembikem]

Yep, I took care of it. Stripping wheel getting ready to powder coat, thanks, big help

 

[likembikem]

Update on my wheels: They are back from powder coating and have new tires on. The rubber dampeners survived fine. I just had to plead with the paint shop to go ahead and do the job with the rubber in there. I have my front wheel bearings in. Going to work on the rear tomorrow. Thanks for the advice. I think I may pc the fork lowers this winter.

 

[one2dmax]

Yep, many don't trust it to survive the 400 degrees they have to get the oven up to.

 

[fmcandrew]

and or the lengthy bake time of at least an hour...

 

[eggohead]

How much does a shop usually charge to powercoat the rims? Those black ones looked sharp.

 

[train460]

and or the lengthy bake time of at least an hour...

wondering what kind of powder they use that needs over an hour bake time?
I am thinking of doing an extra set i have laying around if they will fit in my oven. The powder i was planning on using was i think BIKE BLACK from powder by the pound and it states to cook for i think 15 minutes at 400f
Michael

 

[Fire-medic]

Talk to Patmax on here, he does 'em, he will provide a quote upon request.

How much does a shop usually charge to powercoat the rims? Those black ones looked sharp.

 

[sdt354]

wondering what kind of powder they use that needs over an hour bake time?
I am thinking of doing an extra set i have laying around if they will fit in my oven. The powder i was planning on using was i think BIKE BLACK from powder by the pound and it states to cook for i think 15 minutes at 400f
Michael

15-20 minute average schedule time,after flow out, at temp. Plus extra time to outgas the part at temp.

 

[likembikem]

Sorry so long to answer; mine needed a lot of sanding to smooth out; $200 ....each! but sure look great now

 

[Fire-medic]

:ttiwwp:

Sorry so long to answer; mine needed a lot of sanding to smooth out; $200 ....each! but sure look great now

 

[Poolio]

I paid $90 for my front. He said $90 for the back too. I'll be dropping it off tomorrow

 

[Fire-medic]

My local shop I've used charges $100 apiece, though they may cut that a bit if you have a bunch of other stuff to give them. They will take the nastiest part in and return a very neatly-done piece.

How much does a shop usually charge to powercoat the rims? Those black ones looked sharp.