Search results

This one came with an aftermarket gas cap and a nice extender, so it works fine with the flap. I could just take it off too, which would be fine. It does fit very snug, it didn't come with bolts, and I meant to go get some nice stainless ones, but it seems to be stuck on there pretty solid, so...

Looking good, love the look of the exposed back tire.

You know, I would love to know how ya did this. :) Perhaps you could provide a fella with some guidance? :)

You guys rock! Thanks!

I've been looking all over these things for markings, identifying marks, hieroglyphics, and I can't find anything on them to tell me what they are. They are very, very stiff, I'm guessing they are supposed to be adjustable, but I believe I would need a tool since turning those bottom parts...

Ahhh, here I thought all "belted" tires were radials. Guess I never had much cause to check till now. :) Thanks for the link! Joe

This tire is listed as belted, and appears it would fit the stock rear, wouldn't that mean it's a radial? Or am I missing something. http://www.bikebandit.com/tires-tubes/motorcycle-tires/pirelli-night-dragon-motorcycle-tire The drop down shows a perelli night dragon at 170/80 r15 as "bias...

To verify, it does fit, at least it fits my setup. I did need two of the washers that go on the end, but luckily I had ordered two in the event I lost one, so I just put them both on. :)

So, I installed the corbin seat that I got from Steve, it's awesome! Also put on the stock shifter from a 2nd gen vmax (the 1st gen has the adjuster coming up from the shift lever, the 2nd gen has it going down, the previous owner had modded my footrests to put them back farther, so I had to...

So, do we have any of these plug and play kits available? :) I just got most of the essentials where they need to be, and this would be a very nice investment I would think. Oh, mine is an 85, so I would need the resistor setup, if I am reading all the above correctly. Joe

Great to see your Max kick some Harley ass. :) I've met a lot of nice people who ride em, but there is that small contingent that thinks every other bike sucks. I love my Maxes, always have, but I still look at the other muscle bikes that come out too, and there are a few to choose from now...

This will be my next step, I plan to replace all the fluid (there seems to be some sediment in the bottom of the master, so I figure I'll pull it dry, then push new fluid up after cleaning it up a bit). So far it seems to be shifting fine, time will tell. I keep looking for fluid under the...

I hadn't considered that, indeed that does make sense.

Ok, so one last post on this clutch slave cyl bleed issue. Before I got my mightyvac to bleed the lines, I went out and was just messing with the lever, I took the res cover off and pumped the lever a few times, after a while some pressure did seem to build up, but then, on one of the pumps, a...

So I can look at the prices, can you perhaps post a link to what I would want to purchase? I'm pretty ok getting the whole assembly if it's going to be an easier and better swap in and out. Now, I should point out, after bleeding, it's working with zero issues, and the bike has a little over...

The only place I see a sqare shaped seal is in the master on the handle, and it appears, visually at least, to be fine.

I did not.... I had thought the rebuild kit would include all the stuff I needed.... I won't be doing it right away so if I need extra stuff I can order. What it came with was a spring, two large round seals, a small seal, and what looks like a cap for a bleed port.

Problem solved! At least for now, hopefully I get some time out of it before I see the issue again, I have the slave cyl seal replacement kit, but want to ride her a little before I tackle that job. :)

Ok, I just heard back from the seller of the shifter, and as long as his calipers and my calipers aren't lying, it looks like I'll have a nice snug fit shifter next week. Ordered the factory clip and washer to hold it on, and have the bleed kit ready to clear up the slave cyl tonight. So the...

So, with my redneck modification that the previous owner did to my shifter, I'm still not happy with the way it feels. I would normally just buy a stock shifter, but due to where he moved it, I don't think it has the proper clearance anymore. However, looking at the 2nd gen's shifter, that...