bolt

Am fixing the starter clutch on my '90 and when I removed the flywheel bolt the oil wire that was supposed to be there wasn't there. I didn't lose it, it just wasn't there. I would like to replace it but cannot find one anywhere. Anybody know where to get one? Thanks!

Does anyone can help me by telling what size and what thread does Mark's exhaust cans have for bolting the exhaust tips ? I am sure it is a U.S thread . I need exact numbers so i oreder some new ones

My recently purchased 86 Max came with SuperTrapp Slip-on's that were in terrible condition so I chunked them and installed the stock mufflers. I found out that the bolt that connects the mufflers under the center stand is missing. Does anyone know what size it is and if I can get one at Home...

Broke off before I reached torque spec. Has this happened to anyone? Options to get it out?

For only $13,000 you can have one of the baddest bikes in Michigan! Todd Some measly little GSXR1000 Turbo.... pfftt..... tiny motor = Small horsepower! Here is some power for you! I think this is on a Gen 2 Busa. Sell yours and buy this Mike! Turn Key bad ass! For...

Hi all, I just picked up a 1994. While changing the oil, I noticed the bolt that holds the oil canister on is pretty much stripped. Before I take a vice grip to it, can you tell me where I can get a replacement bolt as it looks specialized from the manual. I tried on ebay but maybe I do not...

I was installing a small bolt (3/8") just about the Oil Fill Cap and I had the Cap off. The bolt dropped. I did not see it go in the hole but I searched on the ground forever and never found it. I fished in the hole with a magnet and got nothing. Unfortunately, I checked the two other bolts...

Hi everyone.. Its been months since ive been on the VMF. Ive been riding like a Hooligan and loving every minute. I have a new Samsung Galaxy s4 phone and the VMF and Sean's site don't work well at all.. For example everything goes screwy when I try using search.. Anyhow.. Two questions.. Id...

Just a dumb question. I am planning to buy a replacement riser for my '98 Vmax. My risers have what I think are the bolt caps. How do you pull out these caps? Just picking them out with something like a small screwdriver? I would assume the allen bolts would appear below like in the...

Anyone know the bolt thread size for the holes in the flywheel? The unused ones so I can attach my puller. Russ

I found a fuel leak, and after cleaning things up tracked it down to the fuel level sensor. Interestingly, it's something the Haynes manual includes checking for every 4000 miles. Tried tweaking the screws tighter, which slowed the leak a little (already very slow) but a little paranoid about...

How hard is it to change the shifter seal I do have a chaindrive so that rear cover above shifter just pops off nothing but bearing behind it ( not sure if the shaft drive had oil in there) and then is it just a rubber lip seal I can work out with a pick?? Also while I was at thunder I looked...

Ok, I have discovered a pretty big problem with my '94. :real mad: Last year it developed a small oil leak at the bottom of the Crankcase Cover 2 or Secondary Gear Cover. Thought to myself: no problem, I'll just replace the gasket. Much to my horror when I pulled the cover off the lobe for...

Man i will never use a ratchet wrench again on these bolts man. :bang head: Outer bolt rear lift hand side. I went up to the yamaha dealer ship with some pictures they said the heads need to be pull off to remove the broken bolt at a cost from $600.00 to $900.00 to repair. Any help on the...

Are most bolt pitches 1.25??? Im away from home cant measure . Mainly looking for sissy bar to frame sock cap screws, handle bar clamp sock screws, the 6 sock screws that clamp forks, button screws on side covers, and tapered screw for the cylinder side covers. Any help is appreciated..I have...

So I have a question that hopefully can benefit myself and others. I would assume that everyone doing maintenence on there bike does always torque every bolt as spec'd and possibly more often torques to what they feel is correct? Maybe I am wrong but I have done quite a bit and am going to buy a...

This looks like a pretty cool new bike. Kind of like if the gen2 and sportster had a baby, or a "wee max". Plus, it's under 8 grand.

While cleaning block up today for my winter project bike, I took some pictures of the 2nd drain plug on the 1200/1300 blocks. On the left side, directly under the middle drive cover there is a 14mm head bolt that goes into block and drains an oil pocket. This pocket appears to serve as a...

I need to replace the hex bolt (as seen in the attached pics) I removed my Engine Guards and want the stock bolt to go back in. Unfortunately I don't have the bolt that came out of the hole so I need a new one. Can I use any old Hex bolt (proper size) or does this require a special steel? I...

Saw on here you could buy the right hand side pivot bolt and nut to get a small bit of movement to align the swingarm. My question is... How do i install it now? book says to torque the left side to 73 lbs but i fear that will snap the Allen key... Anyone done this or know how to do it? it has...