carbs

Every once in awhile a set of carbs comes along that seems a cut above the rest....these are such carbs. They came off a low mileage XVZ1300 Venture (identical carbs as 35mm VMax carbs) with the mixture screw factory brass plugs still in place. Carbs have been completely cleaned and rebuilt...

Pretty cool - check it out. http://www.ngwclub.com/forum/viewtopic.php?f=47&t=49494&start=15

Ok, finally finished sealing my tank, just haven't had the time off work so get it done and back together. So got it back together yesterday and went to start and seems like it's not getting any fuel. Know the fuel line in the tank is clear, blew in it and fuel came up the line and filled...

I was looking at the digi sync tool here on the forum to sync my carbs, had to work today so I stopped by a local used bike dealer and found a Motion Pro sync tool for $50 it was an open box deal, well I bought it. Got home today looked on this awesome site and found the How To Sync Your Carbs...

I have full voo doo exhaust morleys jet kit. when i fire the bike up im smelling gas and or alot of exhaust fumes. what should I check? the a/f are 3 turns out and bike runs strong just hate the strong gas smell.. thanks

I have full voo doo exhaust morleys jet kit. when i fire the bike up im smelling gas and or alot of exhaust fumes. what should I check? the a/f are 3 turns out and bike runs strong just hate the strong gas smell.. thanks

1986 Venture all stock. Has 80K miles. Cylinders showing 170 or better on compression. Using a Morgan Carbtune 2. All 4 carbs at the bottom of the glass. Just barely visible. Cleaned the carbtune and a few drops of light oil applied. Bike used to pull rods about halfway up. Running well. I...

hey guys this is my first post. I'm a new member and I've owned my 2000 vmax for about 2 months. the vmax has been my dream bike since I started riding at 18 with that dream finally coming to fruition in the last couple months. with that being said I discovered recently that it looks like 3 out...

Today I changed the plugs and was going to do a sync with my carb tune and I left the number 2 plug wire off by mistake. To make a long story short now my screws are all out of wack and cant get my idle down below probably 2000 rpms because the idle screw wont do anything. Every time I screw or...

Has it been thought of? Just as the VBoost has the carbs linked 2 and 2, what about adding a second line to link all 4?

With the double d clutch and carbs cleaned I took it for a quick ride yesterday. With that super hard Exceddra tire on it, it spins easily from a 5 mph roll. I was able to pull the front end up high in 1st gear, but not in 2nd gear. I never clutch up my bikes, just pure power. But end result...

So I just got my 85 vmax and I took apart the carbs and cleaned them, and that finally got the bike to run but only with the choke. So I was searching around for solutions and found the shotgun method so I tried that out, it kind of worked and by that I mean it runs only sometimes without the...

I have a 2005 Vmax with 15k miles on it. When I rev above 2500 rpm intermittent backfiring occurs thru all 4 carbs. If I let out the air/fuel mixture screw 6 times it will stop on all but one carb. I know that that is way too many turns and indicated an air leak somewhere. I have used two...

obike ran great last year and every time I started it this winter. Maybe a slightly low idle but not the 5k I have now. One carb started recently spewing gas from the top.vent hose. I removed the carbs but did not fully separate them. I removed enough brackets to rotate the offending carb...

how come when people put on some FCR CARBS they run the vmax without the vboost

As people know....Ive spent quite of a bit of time playing with the bike on the dyno. After that last day, even with Seans kit....I wasnt getting the numbers that I was expecting....I was still too rich, even though from the jetting i shouldnt be. I called Sean for advice (even ordered more...

I still need to drain the bowls and such, but I turned all 4 air screws in then 3/4 turn out and the mystery problem totally went away xD Also, it may just be how carb bikes are, but say I'm cruising along at X rpm, it will feel like the motor is weak initially when I touch the throttle, it...

Hi, * I have cleaned the carbs and changed the plugs of a 2001 Vmax that sat for 10 years. I can get the bike running and it runs great once its been started. It also starts right up if its warm. The problem I am having is with cold starts. In order to get it started cold I usually have to...

I bought a 2005 Max in great condition a few weeks ago and when I picked it up it ran fine with the exception of one of the carbs backfiring on occasion. I installed an Ignitec computer and COP's kit and while the bike became more responsive it would still backfire thru the one carb. Now after...

I sent Dannymax a rack of carbs I picked up from California that was gummed up so bad, the butterflies would not even move and the slides were stuck inside the carb bodies. They had been sitting for a couple of years with ethanol gas in them and were in bad shape mechanically and internally...