front

I have a 4 into 1 Hindle. The front two pipes even though they looked like originaly coted are starting to corrode, Also some back near the aluminum muffler. Can these be recoated?

Anyone have experience using these?? The Good, Bad or ugly :-) http://www.ebay.com/itm/Yamaha-Front-Brake-Rotors-Disc-VMX1200-V-Max-Vmax-1200-85-86-87-88-89-90-91-92-/141542153881?hash=item20f491de99:g:BlwAAOSwm8VUt11b&vxp=mtr

Looking for a decent set of stock front stock header pipes to fit on a 91. Hopefully not too expensive, will need pictures of them :biglaugh: . Thanks

Has anyone installed the Progressive front springs on their 1st gen VMax and was it worth it? Thanks.

I've tried the search engine on this forum and cannot get good results for some reason. The manual says the front fork air pressure should be 5.7 - 14.2 PSI. I read that someone else is running at 0 PSI. Right now mine is 0 PSI. Thoughts? Opinions?

I need some advice. I jumped on my bike this morning and my front brake lever went right to the grip. The brakes are working but obviously something is wrong. All stock except for stainless lines. The master is full and the fluid looks great. No leaks or wet spots and they were working fine...

Has anybody had a severely stiff front brake lever after replacing front pads?? Before I replaced them it had some pull before the brakes would start to grab. Now when I pull it they almost grab instantly, but they do release, they aren't dragging. There just seems to be no free play to say lol...

Looking for all of the info possible to make a successful swap, any and all info would be great Sent from my iPhone using Tapatalk

? Sent from my SM-N920T using Tapatalk

Front tire is slowly leaking around the bead. I was wondering if certain years have this problem? Since, mine is a 98 and has the black rims. Is this only happiness with the black rims? It's a new front tire. It has 1000 to 1500 miles. After reading in the wheels/tires section. It seems like...

Front tire is slowly leaking around the bead. I was wondering if certain years have this problem? Since, mine is a 98 and has the black rims. Is this only happiness with the black rims? It's a new front tire. It has 1000 to 1500 miles. After reading in the wheels/tires section. It seems like...

Having a minor issue with Woona that could easily turn into a disaster. The front brake lever feels like it is catching, which makes it difficult to have proper control over the use of my front brakes. https://www.youtube.com/watch?v=QL8oqDfmt20 Any thoughts on where it could be causing...

Can you use Race techs Gold Valve Cartridge Emulators with a Progressive front end lower kit and would there be a difference with them then with out them? Thanks.

I bought the Delkevik OEM front pipes to replace the old ones on my 2000... I've never done this before...but going to do this myself because I want to learn... The old ones came off easy with the mufflers still in place...and cleaned out the old gaskets... My questions... The Delkevic...

Hey guys. Hope this hasn't been beat to death, but lots of searching yielded no answers to what I'm after. I just picked up my Vmax and it needs tires. It has a 17" rear wheel, and an 18" front wheel. It currently sports a 170/60zr17 rear tire and a 110/90mc18 front. I don't feel like this is...

Just got new turn signals for Father's Day. Rears went on fine but the front ones are three wire assemblies? Tried both ways and all I get is a solid light with a relay clicking noise when I activate turn switch? Light stays on solid with no blinking. Help please

I'm working on a set of frame sliders and would like to use the front engine mounts as a connection point. Currently there is a long rod that runs from side to side across the front of the engine. I'd like to replace that with individual bolts on each side. Does anyone know why they used a...

Please help I am putting all new parts in my 1985 wheel that I got and I am confused. The spacer is smaller than the inside diameter of the wheel. Is that normal? As wheel there is a spacer flange that goes in and I'm wondering does it slip over the spacer, butt up to it, and which side goes...

I wanted to change the spark plug wires and caps on my 1994 and while the back as easy, the front are a pain. I'm attempting to remove or at lease slide the electronics tray enough to access the coils but I can only pull it out so far. Any tips or hints would be helpful. :bang head: Doug

After replacing the springs with Progressive springs, the front end of the bike feels like it is high and stiff. There is very, very little bounce in the front end. Maybe this is normal but before I changed them I could easily bounce the front end up and down by simply sitting on bike and...