kit

Here we go again.... there is a wiseco +3mm big bore kit with a 10.5 compression that will yield a 1394 cc. Has anyone done it? what do you people think about it if I am going to use an older Royal star Block with Vmax heads. Any ideas? shave the block? shave the heads? nothing radical, but I...

Hey guys I have an 86 vmax I out together a kick ass kit using 6 piston calipers morleys brackets and ceramic pads here's a link. I need money to rebuild my engine in my car. OK, to clarify what you have. $60 Adapters/Bolts to mount Hayabusa 6 Piston Calipers on 85-92 Vmax Forks. This requires...

Being a bit short, 5?7? with a 29 inseam I have always wanted to lower the Max a bit. Did the Corbin seat, took sending it back twice before they cut the foam the way I wanted it. When I first rode the Max, I was on the toes at stops, hated that feeling, bike is too heavy. With the seat replaced...

I currently have a Kerker 4 into 1 system with a K&N filter. I am looking to go to UFO Dragster pipes with a full Stage 7 kit. Can anyone tell me what kind of power gains I can expect and what the pros and cons would be to go to this setup. I believe the UFO setup would be quite a bit louder...

Hi. I've a full exhaust system on my bike with stock jets. I've been told it would be a good idea to up jet to stage 1 0r 7 What are the pro's and cons of both? Will 7 cost me my v-boost? Is there much real world difference betweeen them or is it just the seam of your pants difference? Any...

Hey all, got Sean's jet kit installed today. Had a few issues, of course, but all in all not too bad. I had never messed with the carbs on anything before so I took my time and kept coming in to look at the appropriate stickys on here. The only real problem I had was getting the T hooked back...

Hey all, I am going to send Sean my stuff next week to get his muscle kit. I am confused on what exactly I am supposed to send him though. Is it just the lid of the airbox or the whole thing? Also, does anyone have his kit that is using stage 1 needles? This is what I currently have, and if...

Hey all, just had a question about Sean's muscle kit. Is the crankcase breather hose absolutely necessary? I'm just worried about the hose leaking and wonder how much hp does installing it really get. I am getting ready to order from Sean and just want to make sure on this part of it. Thanks.

Hey Guys, I'm desperately looking to eliminate the "extention" in the rear fender which hosts the license plate and the turn signals, but I don't want the plate hanging out above the tire like in most kits I see around. Also, once I eliminate the original turn signals on the back, I want...

Im looking to replace my brake and clutch lines with ss line's does anyone know of a full kit for a good price. I want good banjo's and clear coating on them. Also can i get ss speedo throttle cable.

I'm interested in upgrading my front fork, which seems like the best bang for the buck in increasing handling according to a lot of threads on this site. It also seems like Race Tech springs are slightly more favorable than Progressive's springs, so I think I'll be ordering a set of Race Techs...

Hey all, I am really close to pulling the trigger on one of Sean's kits. Instead of trying to filter through all the previous threads, thought I would start a new one specific to my bike. I currently have a stage 1 with a Hindle 4-1 installed by po. Does anyone know if the stage 1 has...

Hi Guys, I have just obtained a OTEC clutch upgrade kit but the supplier was unable to provide any installation documentation and I have been unable to find anything other than this works with the standard plates. Has any one installed one of these? Do I fit the standard clutch plates as per...

I am thinking of getting the vmax ground cable kit for 23.00 .Has anyone tried this?.

Does anyone know where to find a rebuild kit for the front resovior ? Is it the same as the clutch kit? I've been scoping eBay for one but don't think I've ever seen one. Any ideas? Thanks, Ed:ummm:

hello, new here and hope i'm posting in correct sub-forum. i recently purchased a 97 Max, and I want to have carbs rebuilt and a Dyno Stage 1 kit (or similar) installed. i can tell there are issues with the carbs (smell gas, some minor back-firing etc) and figure since the bike is 14+ years...

Wondering how to install this thing the hose t fitting any pics on yours

Does anyone make a hose kit for the 1st generation V-Max. I'm thinking if I order them piece by piece from Yamaha it might get a little expensive. I noticed one of the carb boots is cracked also, so I might as well replace all the rubber around the carbs to. This is a 1988 model that hasn't...

Im going to be installing a stage 7 kit in my 2005 max. Was wondering if anyone is useing the max air kit from python motorsports with a stage 7 and does it work well... If anyone has any other suggestions about what will work the best (with a stage 7) my ears are open . I am pretty much...

So my clutch started slipping big time....any v-boost in the first four gears would result in major slipping. 25k miles on presumably the original clutch, so I got the "full kit" from PCW, which runs about $160 after tax. It includes eight full friction discs, the HD spring, and a new cover...