marks

I like Vance&Hines slip ons that are made for new vmax17. I would just need good headers, and I was thinking about marks, would that work? Vitek

hey guys. I ordered my Marks exhaust the other day. How hard was the installation? I know with my hindle exhaust the rear was an absolute pain to do.

Ordered the 4-2 Marks today. Anyone on here have a good starting point on jetting , needle pos., mixture @ sea level, etc......with the exhaust? I also drilled my slides, so anyone with similar setup I'd appriciate your input.

So after installing the Marks pipes, K&N air filter, fuel filter, and new spark plugs, I decided to dig into the carbs after occasional exhaust popping would not go away. Carbs aren't bad to do, but are time consuming. I found that all four of my float levels were set way high from the factory...

does MARKS exhaust have an email address?

Didn't want to break tradition, so I figured I better post pics of the new system. I still have to raise the saddlebags up some....wish I could take them off for good, but they are really handy when you need to haul stuff, especially beer!

Been getting moisture marks at the joints of my Marks exhaust. Anybody using some high-temp RTV sealant to seal the joints, or should I just let it go?

got my bike back running after several mods and repairs, THE EXHAUST SOUNDS GREAT!! Got a couple of leaks but i didnt use new gasksts so I think thats the problem.

Just ordered mine today, and Mark said he only has a few sets left! Anyone on the fence about buying a set for this sale price better hurry.

Thanks for all the input was torn about what to do? Was going to buy a supertrapp from Sean. then I found some local deals on used systems. But I just ordered a system from marks performance! Right now I have a stock air box with a K&N filter needles shimmed, stock jets. But I also have a...

Hey there guys. Got a question. Not sure if I will have the definitive answer I'm looking for: Which exhaust will provide the most power. I know this is a classic exhaust question and will boil down to a lot of different opinions. I would prefer an answer backed by dyno. I think I recall a...

anyone live near Hesperia, California. Marks exhaust? I want to have a pipe made for me thats upswept like a ducati or the old 2 bros slip ons. Problem is Mark sold his bike 9 mos ago so now has nothing to mock up against.Now he cant do anything different than what his jigs are set up for with...

I want to have a pipe made for me thats upswept like a ducati or the old 2 bros slip ons. Problem is Mark sold his bike 9 mos ago so now has nothing to mock up against.Now he cant do anything different than what his jigs are set up for with out a bike to use.I am hopeful that someone lives close...

Does Marks pipe use the block adapter and clamp band for the rear headers or can I remove this little piece. I am trying to get the bike ready for the arrival of the exhaust.

Alright Yall talked me in to the Mark SST 4/2 pipes(Yeah the Mod Monkey hit fast). What exactly will I have to do to have the bike tuned properly after I put them on. I'm not a carb guru but am pretty good with a wrench. Will I have to take it somewhere to get it tuned after install? Not sure if...

Says domain expired. Wanted to check out his exhaust.

I ordered a stainless exhaust from Mark two weeks ago and it showed up at my door yesterday. The bad part is that I am away at work for another two weeks yet. So this is a slow torture for me.

Hi, I just got my Marks pipes on sounds and runs good. I do have a low end slight stumble around 3-4k then it clears up thru the revs. I checked the plugs and they seem like a nice brownish color. I heard they are lean on the bottom more so than the upper range. As far as jet kits I still...

I'm considering going with a Kerker 4-2-1(or possibly Marks 4-2-1, or big tube 4-2-1 of some kind???) instead of my Marks 4-2. Anyone wanting a nice dual setup? Its a full SS system. Has dual 14" alum cans. I have the straight tips and the sportbike-like turn down tips(just bolt in). I had the...

Hi Guys, I took my UFO exhaust off last night and it went well. I found that the read cylinders modst inner allen nut are almost impossible to get to with a regular "L" shaped allen wrench, I can't see how in hell to get a torgue wrench in there to torgue them. In fact those 2 inner...