steering

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Buck8154

    Steering Wobble?

    Went out for a short ride today and noticed that after accelerating and letting off the throttle there was quite a bit of wobble in the front end. It only happened if I was going more than 40 mph before letting off the throttle. Not sure what is causing this...any ideas? Thanks in advance.
  2. R

    Identifying steering wobble

    I was passing a car on an onramp this afternoon and hit about 85 to 90 I would say - I made a fairly sharp turn around the car to pass and the steering started to wobble, not really a wobble like I have had when I had misaligned forks on my previous bikes, but a smooth side to side sinusoidal...
  3. D

    steering Crown

    I have searched the service manual and didn't find it. Can anyone tell me what the size of the wrench needed for the steering crown(bolt on top of the trees). I think I have the right name. I would rather not use a large cresent wrench if I can one the right size.
  4. D

    question on steering test

    Okay it may just be me. When you are testing the steering by seeing if it falls all the way to the stop. Do you take all the weight off the front end, or do you just put it on the center stand. Just on the center stand mine stays where you put it. But if you lean on the back alittle to take...
  5. bikedave99

    Steering Head Bearing

    Alright, this will be a little pictorial in how I tore down the front end of my 1989 Vmax and removed and replaced the steering head bearing. Now, I didn't have any of the typical high and low speed wobbles that I could tell. This could be because my bearings were so bad that they kind of sat in...
  6. bikedave99

    Steering Head Bearings?

    Where do you guys get them? I am going to replace my steering head bearings to the tune of lvlhead's instructions but need some bearings to start with. Thanks Guys!
  7. dannymax

    Easy steering head adj. tool

    Here's a pic of my homemade steering head nut adjuster tool. 3/4-2 adjustable spanner (usually on e-bay for $10 or so) Drill a 3/8" hole in handle, square it up to receive torque wrench Works pretty good for me dan
  8. T

    steering lock

    I recently purchased a vmax with a bent frame. I have since replaced the frame with a frame I picked up from a salvage yard. I am wondering how I can replace the steering lock with the one from my old frame? The salvage frame did not come with a key and I would like to get the steering lock to...
  9. B

    just replaced the steering bearings...

    The worse part was getting the races in and out. Inserting the bottom race was the big pain because of the way it sits. We improvised a tool for that one, a three d-cell mag light that was already broken. Worked perfectly. :)
  10. Shuriken

    Best steering head bearings?

    I will probably end up replacing steering head bearings. What bearings are worth installing? All Balls? OEM?
  11. COP RUNNER

    Steering Damper

    I HAVE READ THE THREADS ABOUT THE DEATH WOBBLE'S & THE FURBER FIX , ( HEAD SHAKE ) , DOES ANYONE USE A GOOD STEERING DAMPER & DO THEY WORK ON THE V-MAX ? :ummm:
  12. gleno

    How do you replace the steering head bearings?

    Well I’ve read the service manual and I've searched the forum for a post or set of posts that gives a step by step on how to replace the steering head bearings and it doesn’t seem to exist. :confused2: There is some general information on assembly disassembly and adjustment but not on...
  13. D

    steering bearings

    How hard is it to change them out? The top nut on mine wont budge AT ALL! any ideas???? is there a special tool??
  14. m-cman

    Steering Bearing Removal

    I have read every post I can find on this subject but haven't found an answer to my question. How can I remove the lower bearing without damaging it? I want to chrome the triple trees and need to remove the bearing. If it can't be done, does the factory replacement bearing have the rubber cup...
  15. Remeber Me

    Where to buy steering nut spanner?

    Where is the cheapest place to get the spanner for the steering nut? Is this a dealer only item or can it be gotten anywhere for a good price?
  16. jgotko

    1992 Low Speed Steering Wobble

    Guys - Was going about 25mph and went over a small bump and front end began to wobble. What could be possible cause? I verified everything is tight. I tried to check the air in the Forks and read nothing. I think the air fill valve is no good as I didn't get any air out when trying to exhaust...
  17. S

    steering torquing without removal

    all the instructions i see for torquing the steering head bearings call for the bike to be on the center stand, and handlebars removed. is it possible to do it while the bike is just sitting there. I dont have a center stand, but my new to me vmax needs some torquing. any ideas?
  18. maleko89

    Steering bearings

    After 2 years, I'm finally going to take the time to replace these bearings. I'm going to order the following parts from University. Anything else I need? Thanks. Mark #1098 93332-00001-00 - bearing 93332-00008-00 - bearing 1J7-23415-00-00 - bearing race cover
  19. mabchewy

    Steering Stabilizer?

    Looking for steering stabilizer options for the V-Max?
  20. firefly

    How to test your steering head bearings

    Take your bike for a ride through a series of potholes and bumps at straights, a curve with a bump or a pothole in your path and feel how the front reacts, if it feels rubbery with a side ward jolt this is a loose steering nut all that is needed is to re torque it, regular checking and torquing...
Back
Top