Search results

This is a heads up. I bought a widened swingarm for my *cough* hd *cough* from chassiswerks online store. I didn't get it. They said they were covered by insurance, and would send another one. I still didn't get it. They said they were covered by insurance again. I asked them for...

You can separate the compressor from the air horn easily. Makes fitment easier. There are 2 retaining points. Then it comes apart. I'm sure you can see what needs doing. :punk:

I have to repair a rearset and I want to change the thread size. I thought the chinese pegs I had would be 8mm, but they aren't metric. So, I want to make them suit Kuryakin pegs. What size thread do Kuryakin pegs have? :biglaugh:

I never knew this section was here! I just tripped myself out by finding it! When I pulled apart my carbs I dropped one of the bits of plastic that goes over the choke shaft. The thing shaped like a top hat. I've since cleaned the floor and filtered all the dirt through my fingers, with no...

This chick would be --> http://www.facebook.com/BrookeWeisbenderFanPage :biglaugh: She' likes a hamburger with the lot!

I think that the original seat design was pig ugly. That middle piece looks stupid. I'm going to use this thread as a record of doing a modded seat. First thing is to check if my idea will work. :biglaugh:

Is blowing through the fuel line with your mouth a good test of a needle and seat, or am I just being a dumb-ass? I seemed to me that my no 4 needle and seat was acting all funky. Seeing as how it's heading towards the end of riding season, I thought that I would be better off ordering a stack...

Here's a picture of the speedo I put on Veronica. I've been toying with the ides of fitting this plastic thing to her to tidy up where all the wires and top triple clamp are. I'm thinking of cutting it down about 3/4" or 1" and mounting it kinda like this. Do you think it will look...

One of our foster kids got adopted today. This is Jethro. It's so sad seeing them go. I wanted to keep him forever. He's just a pup, 4 months old, and is 15kg. I fed him a whole bag full of jelly beans before they came to look at him, but they still took him.

The forks are a bit out of sync with the bodywork, but overall I think it's nice. :biglaugh: http://www.bikeexif.com/triumph-bonneville-xenophya

I just went for a ride after putting in my Morleys jet kit. My setup is I used Seans needles (stage 7?) Put in the air correctors 157.5 mains STD springs Idle screws 3.25 turns out V-boost programmed to start opening just before 4000RPM Seans airbox lid Marks exhaust 4 into 2 The main...

I have tried searching using words like morleys muscle jet install* fit* blah blah blah and I get like a gazillion posts that have some of those words in it. Is there a how to guide anywhere? The instructions on Seans website are pretty short, and I can't work out what I should do to start...

http://www.youtube.com/watch?feature=player_embedded&v=lFISPsYjk4E

Is it just my eyeballs are in crooked, or has it been scooped out a bit already? :ummm:

I can't find any posts detailing how to fit up the Marks 4-2 system. I guess it's straight forward, but I know the frustration (and damage :rofl_200:) that comes from doing things the wrong way around. Is there an order that is best? Do the rear engine pipes go on first? Do they cross...

I think it would be a good idea for us to have a thread for our adventures in the world of powdercoat. A place where we can document the colours and products we used, and the results we get. I'll kick it off with my side covers. I got a good set of 85 side covers off a bike that had been...

Part 1 I have successfully connected my v-boost servo to an Ignitech ignition module. This allows me to program the servo motor opening according to engine RPM, and also adds the ability to change the servo position according to inlet vacuum readings from the MAP sensor. Servo position can...

After a long long time, Veronica goes VROOM again. :biglaugh: Thanks to all the people on this forum for their parts and advise. You help has been invaluable, and is very much appreciated. Rock on! :punk: After a test ride a few days ago I had to tighten a hose clamp, tweak the...

After reading another thread on here I decided that I didn't know what I was doing, and decided to pull my clutch back out and sort it out. The first pic is of the KB frictions. They don't have any notches. There is a pic of the clutch components in order as they came out of the basket. There...

:eusa_dance: :biglaugh: :punk: http://www.youtube.com/watch?feature=player_embedded&v=oumzuQPCtlE I think I want a Chrysler.