air

Trying to decide if I pc my scoops gloss black like everything else, or if I do them chrome silver, or if I get a set of chrome scoops. I am not sure if I like the shine of chrome scoops, but not sure if I would like the all black scoop either. Anyone with pictures? Lee didnt you do your...

Hi, I just rebuilt my carbs and when i put it back fuel was pouring out. So i removed the airbox to see where fuel was coming from and it's pouring out the air jets. I tried to cover them with the fingers, the it came out of the tubes that go to the airbox... When i rebuild the carbs i...

Hi folks. This is not a VMax-specific question, but you guys are the best web folks I've dealt with, so I'll ask the question here. I'm working on a 1994 Honda CB1000, and I want to install individual air filters on each of the 4 carb bodies. However, 2 of the filters would have to have...

Hi, I just installed Morley Jet kit and now it sucks at higher RPMS, I cant even get to 6000 RPM. I did this while i was cleaning my carbs and my new exhaust hasn't arrived yet, so it's still on stock exhaust. The problem is i read CV carb tuning guide and it says if it doesn't pull well my...

Stupid question!! I can't find another hose where does the small port at the top of picture underneath airbox go??? Sent from my SCH-I535 using Tapatalk 2

Stupid question!! I can't find another hose where does the small port at the top of picture underneath airbox go??? Sent from my SCH-I535 using Tapatalk 2

I remember at one time something about removing a brace of some sort in the air box cavity, ( less restriction for air flow ) can someone refresh my memory? and give me a quick how to reply. I only had my ( new to me 09 ) for part of last summer, so im just now starting to throw some...

I have been reading this site, Im new to it and I love it. Tons of good information. I was wondering, and I havent found a thread yet, can the scoops on the side of the carb, tanks be used or set up as ram air? I saw some aftermarket ones for sale, which were very overpriced. I was wondering if...

inside the velocity stack, yamaha created a high velocity port just before the carb venturi, meaning they made the velocity stack smaller by 19 % , for about 1.5 inch to accelerate the air speed to get better atomization at the needle and get more air into the pilot jet. did a test cut the...

Is there a difference in fuel (main) jets vs air jets? or are they one in the same just different sizes and makes, mikuni/DJ, Thanks.

I need some troubleshooting advice or ideas... At times I need to need to bleed my clutch. I use a mity-vac and sometimes it will last for weeks and other times only a ride or two before needing re-bled. I've replaced the slave cylinder and cleaned up the masters top edge...it looks fine so I...

I have the K&N pod filters with dynojet stage7, full 4-2-1, ram air head wind gust makes it cut out, it has air correctors, what are my options here? modified air box? and would I need to remove the correctors or not, what do have for me Sean? I'm ready.

I'm going to use the above as it will work with the intake I am using. Is it best to use a dynojet kit with it or the morley jet kit ? I'll be running a full custom exhaust.

Has anyone ever used these personally? They are cheap for a pair & I know most run progressives but I am on a tight budget & the factory shocks dont do it for me as I am always riding w/ the wife. I will be changing front springs this winter to progressives but would like to change rear also. So...

So, I need some advice on air compressors. I was planning on buying used, but honestly I don't trust the meeting someone off of craigslist in a parking lot when I cant tell if it works or not. I went to a few pawn shops and couldn't find any the right size. Now I am planning on just...

On my '97 I've noticed some rough spots showing up on the scoops. I'm guessing oxidation. Anything to do other than paint them? Sent from my DROID RAZR using Tapatalk 2

There are 2 nipples on bottom of the air cleaner box. One is the pcv inlet. There is a small nipple at the front bottom on the un-filtered air side. What hose fits here?

The question is, what do you think of them. A three hour ride on the factory Vmax seat is brutal, at least for me. I've ordered a Corbin seat for the bike, but I'm also thinking of an Airhawk cushion. The theory makes sense. It should even the load. Just wondering what experience people have had...

Hi guys can't find out how much the stock air box flows. Mine is horrible to keep clamped onto the carbs, I know stupid resin to change box but I'm tired of playing with it. What I want to know is the cfm so I can make a 1 pod filter in to 4 carb cold air intake and keep the stock jets.

There is a listing on eBay for pods that look like pitbike filters.it says in most cases you won't have to rejet,maybe adjust a/f screws some.is there any truth to that or will carbs freak out?it would run the same as removing airbox,correct?