end

Put in the Morley stage 7 jet kit and marks custom 4 to 2 exhaust over the winter. The bike has run great. It does run a little rich so I backed the clip off the fuel needle one notch. Helped out a little. Ran the bike for 2 months and felt fine. Just ran it the day for 150 miles and the last 20...

Hi, I just bought myself ricor intiminators, progressive springs, new seals and head bearing. I assume that you'll need to remove the forks to get these stuff in there, so how do you guys secure the bike so that the front end is raised? I've read the forums about how to remove front forks, but...

Hi, I'm looking to buy an '07 used exhaust from a nearby CL add to replace my dinged up left side muffler on my '88. As I'm sure you know the end caps on the '07 exhaust are black whereas mine are chrome. Knowing very little about how the exhaust is put together, it appears that I cannot...

I experience a serious wobble around 110mph on my 2005 VMAX. I had the front end looked at for problems but none were found. The dealer then told me that this was a common issue with these bikes and not to worry about it. I can't not worry about it so I'd rather find a solution. Is this...

I've been told that they hayabusa stem offset is different to the vmax, does this make any (adverse) handling issues?:worthy:

Hi i was wondering if anyone has attempted using the venture frame (1983-85 - 1200cc) just to get the monoshock look? I am not looking to add all the other rubbish/dead weight, basically just looking for a monoshocked rear end to my vmax, which would give me a springboard for further mods...

I was planning a play by play when I did the install, but it was a comedy of errors, so here's a run down of the meaningful part. My 2003 Vmax had about 4200 miles on it when I purchased it. While it had no crash history, it did have tale tale signs that it had fallen over in the garage or...

I

Hi all! I am determined to get my VMAX back on the road. It has been down for 2 years. Here is what is going on.. It won't idle. When I am driving it it feels fine. Pull in clutch, dies. Stop and go traffic I have to keep reving the engine to keep it running. I took it to a repair...

HI GUYS I am a newbie to the vmax, have been riding for 56 years. I need to know if there are radial tires available with the stock sizes. ON A different topic I need to find out if what is involved in raising back to stock a REAR end that has been lowered. bought my 02 a couple of months ago...

Buy All The Guns You Want,,,,,, BUT..... "We have looted the future to bribe the present, and at the bottom of the cliff the future is waiting for what we owe it." Mark Steyn Hillsdale College lecture 2013 Verified this, it is the truth. Obama is tearing our constitution apart, why isn't...

my exhaust system is finally comming to what i had in mind. this is a first impression. ,headers are going to be also mirror finish. shor end cps are going to be gold chome like my fcr inlets. i am so anxious to see it compete Sean Morley hooked me up with this system after a lot of questions...

Ok , looking around for a friend to see if anyone knows where I can get the center section for a Ford 9" rear with 3: 91 gears in it, or buy it new if some one knows who sells this set up . Have checked with Summit , Currie , Jegs and a few others , everyone offers a 3:89 but he wants a 3:91 ...

Just wondering what options there are for new and better forks? I won't be getting into this project till later this year but was wondering what my options and cost will be. As well if anyone has some pics of different setups plz post.. I'm hoping for one that I can add a steering stabilizer...

Hi guys. I just acquired a 2001 V-Max that has been sitting garaged for 4 years now. It only has 9700 miles and looks perfect. The carbs were NASTY. Everything inside was gunned up and nothing would move. I took the entire thing apart and cleaned in Chem-Dip. All the parts look new and...

I bought bar end mirrors and love them for the great vision they give me of my surroundings but my problem is finding grips that I can use that are long enough to reach the end of my bars. Anyone running bar end mirrors and have grips that look good and match up with the bar controls can you...

So my question has to do with what the bike is looking for to achieve more low end torque. From the stock bike you can add stage seven and that tends to give you more top end power, you can go to morleys setup and get more even power throughout. Now what is it that makes more low end torque? Are...

the end of spark-plug as it is scince 100 years http://www.sae.org/mags/aei/12102/

Hi, I got the UFO megz and when i was repacking the exhausts, one of the end caps got stuck really hard. It's a bit angled. You guys have any suggestions on how to remove stuck end cap without damaging the finish? Thanks!

My tire was about to be over, so here it's the end ;) http://www.youtube.com/watch?v=yKni9g6ZbFE