end

Hi, So i just put on UFO exhaust with morley jetkit. I have the air corrector, modified airbox and PCV connected and read on http://www.vmaxoutlaw.com/tech/cv_carb_tuning.htm that you begin with tuning the top end with main jet sizes. The problem is that I can't even get to the top end...

after a 1000 mile on my max my front brakes have started making a knocking noise .i have taken then pads out and notice a ani squeal plate was loose. i tightened it up (now brake pins are a tight fit ) done 200 more miles its back with a vengence wtf please help !:bang head: ps i know its the...

Looking for some pictures or ideas on how everyone is strapping your front end down? I was thinking just ratchet straps but not sure if that's how everyone is goin about this I would be riding the bike to the track so can't really be permanent

This new law will in a way make our discussions here a felony!! It is now a felony to assemble and protest under federal law. Obama and Congress with the Senate apparently do not like what we the people have to say. So since they cannot make us shut up, they just made it illegal. This law is a...

Hi i've been looking thru this site looking at gettin some info on why my friends max is running so poor and have a question, I see some of you run with the boost valve fully open all the time, does this not cause overrichness at lower speeds ? or do you down jet on the pilot circuits to...

Damn lately it seems like one thing happens after another & I am not talking good stuff. Just found out Christines Mom has Lou Gehrig's disease.

As I've read this is very common to these bikes. With mine it can start as slow as 160km/h although usually starts around 180km/h. For my bike I find that if I push against the bars I can get around it happening. I must keep pressure on them whether accelerating or decelerating till I get below...

I am looking at getting some new handlebar ends and new mirrors for the Vmax. My brother is running those handlebar end mirrors on his Triumph and I think they look pretty good. I would be interested to see them on a Vmax. Has anybody used them? Good or bad? Just wanted to get an idea of what...

So I've got the the front forks, axle & calipers from a GSXR 1000, and of corse fitting it to the max is the next upgrage I want to do. But I still need a wheel and rotors to match, Can any one tell me of other models that use the same wheel as a 03 gsxr 1000? Cheers,

I just picked up this 2007 R1 complete front end as well as a cycle one off tripple tree for usd forks. I'm excited to install, which doesn't seem to be very much trouble, but does anybody know what type of timeframe I'm looking at? 8 hours expectancy overkill? 4 hours? Thanks!

Hey Guys, new to the forum. I have a 2000 Vmax that I picked up last year low kms (15k kms now that I added 5 or 6 to it this season) The bike needed a bit of work as it had been in storage for 6 years.... So I have done the basics to it - cleaned out the carbs, soaked them, cleaned them...

Ok, ive searched and searched, and I guess before tearing it all apart Id like to see if somebody has experienced the same thing that I'm experiencing The bike is a 99 vmax with 24k miles on it. It feels great on flat roads and brakes are solid, no clunks or anything. However, at any speed...

Trying to decide where to go with this. Yammy spec for ring end gap for the stock pistons and rings is 0.0295 total/measured, no stipulation whether it it's 1st, 2nd or oil ring. General consensus from current info is that a n/a hot rod motor needs about 0.004-0.0045 per inch of bore...

Does anyone have a set to sell? These things are insane expensive at $25 a piece retail. These are the open 4" 6 bolt caps. Thanks!

just got a 86 v max it hasa wobble when slowing down anybody know of a dampner for the max :ummm:

Hi guys I went to a different type of grip last year and I hated them so I want to put the stockers back on but I broke one of my end caps... Anybody got one they want to get rid of cheap or know where I can buy new ones at?? Thanks in advance!

Hello everyone. First of all I have bar end mirrors now that I got off eBay for like $25 2 years ago. They were ok for awhile but from taking them on and off so much they just don't stay tight anymore. Now I love the bar end mirror concept but I was wondering if anyone has a nice set that they...

Well guys i started joining a couple bits and came up with another option for the vmax. Don't know if anyone already used this one or not (kawasaki ZX9R). This one came out pretty good i think. Polished with black matte and golden... Now just need to wipe the dust off and deliver... Pretty cool...

I received my supertrapps today (used) - I am confused about the end caps, the pictures online show disks and a closed dish end cap as standard. These have a first inner disk with a triangle plate tack weleded in with a small central hole about 10mm / then two normal disks / then an outer...

Decided to extend my front end a little just so my front tire is about 10-12 inces farther out. I have the newer 43mm front end on now and was wondering can I just get longer tubes? I really don't want to change the tripletree because mines already chrome and Paul from MadMax wants way too much...