needed

just like the subject says... Looks like my R/R has taken a dump, after looking perfect yesterday, again today I am getting near to no charge, just about 12V at 3k rpm. :confused2: Checked the stator output and it's fine, so I'm on the market for a new R/R. I'd prefer a 96-07, or any other...

So I did a cosmetic teardown just to do some heavy cleaning. I get it back together and she cranks over nice but no spark. "Dollar Bill" Manny gives me a few CDI boxes to try and nothing. He tells me to check that little square relay just behind the downtube right in front of the CDI box. I...

does anyone have any pictures of a kerker 4-1 uninstalled by itself so i can compare it to one i just bought? thanks in advance i cant find a decent picture anywhere

I need to get a new starter clutch assembly, what is the on-line dealer of choice these days? Got a VMOA member # for discounts if available. TIA, Kenny.

I was helping a buddy out today on a new/used max he picked up, it's been sitting for a few years so I went through the carbs, cleaned them, new plugs, brake fluid etc...I got the drop cylinder sound to go away, I think it was a plugged carb passage but it still runs a little pukey, It has...

Now i currently run the stock bridgestone G525/526s on my Max , im more than happy with them . Replaced the rear not so long ago but now i find out that Bridgestone here in New Zealand have a new supplier so now i cant get the G525 for the front . They do have a Bridgestone R 110/90-18 G510 HTL...

Somebody had mentioned that they were using an electronic integrater that allowed the rear turn signals to be used as running lights and/or brake lights. I did a search but it must be buried in a thread somewhere. Anyone out there familiar with such a device and where to buy it? I know Kuryakyn...

Hello, I'm going to pick up my 2007 VMAX Tuesday and it's been about 10 years since I sold my last VMAX so my memory is not so good. Can someone tell me what tool and size of tool I'll need to Move brake lever assembly and/or switch assembly. I have to drive it back about 550 miles so I...

I need to get new bolts for my muffler mounts. While I'm ordering, I figure I might as well get some of the other bolts that may be an issue. Anyone know what size bolts are needed for the following items?: Muffler mounts Diaphram covers Fuel Bowls Anything else that is commonly an issue...

I know there are some fans of the FZX 750 Fazer who live in this forum and I need your help. I have the opportunity to buy a well priced low kms Fazer for my next project. I want to build the bike pictured and I'd like more information about it. I have seen a similar project bike on the net...

Looking for spring and bolt for pivot on center seat. Posted ad in wanted section but thought might get more exposure here. :th_11: Thanks Paul

OK guys, need to see if anyone has any extra shims in the 258 and smaller range. Really need a couple of the smallest shims (220). I have plenty of other sizes I can trade if anyone is interested. Sean

Hey guys - I'm in South Florida (Broward County). Can anybody recommend a good mechanic. I'm definitely willing to travel. Thanks for your help. - Mark VMOA mdr-5041

AHHHHH! Ok I am installing a Carrozzeria rear wheel. If I torque my wheel to the recommended 42.5 Ft/Lbs. I get binding of my wheel. If I back it off there is no way the nut will stay torqued. I have checked it multiple times and I cant find where the bind is. I swear to God I...

I am planning on buying a 150CC scooter due to the gas prices. I drive 60 miles round trip to work 4 days a week in my Maxima that gets 22 MPG and my VMAX is just a lil better. I spend about 65.00 a week in gas. So I am planning on buying a 150 CC scooter to drive back and forth to work, and...

I received the below email from a local PGR Captain. Four boy scouts recently lost their lives (ages 13-14) at a campground in Iowa during a tornado. The disgusting fuckers at http://www.godhatesfags.com/ have decided to PROTEST at the funerals for these young men. On their website they actually...

Does this tire fit the stock rim and clear the stock swingarm? Just picked up a nail and I need a cheap one for the summer until I do the 18" conversion. I can get this one shipped for $84.00.

OK guys, Anyone out there have any shim kits? I am looking for a few shims that I currently don't have. I need (so far) 2 shims - 2.40 and will be setting the rear head this evening and will see if I need more. I would like to get a few shims in thicknesses from 2.00 to 2.55 and 2.90 and up...

Please show us your rearends - on the vmax that is! I thought I would start a new thread for this one. I have recently bought a new 18" rear rim and there's a 3/8 inch offset, but tire lines up in swingarm perfect and tracking is good - I want to see pictures of different custom rear...

Helllo everyone, I am a bit new to the Vmax bikes as I have purchased a 2003 Vmax. I found it with only 1500 miles owned by a blackhawk choper pilot who had spent alot of time in Iraq since purchasing it new. I wanted to get a set of saddle bags. Can anyone provide some guidance regarding...