stage

I recently purchased Morley's muscle stage 7 jet kit/ Marks 4-2 exhaust for my 2006 vmax. I am trying to see if I can get some help with seeing what other people have their jets set to so I can have the best possible starting setup. I also was looking to see if people had any pointers or...

Hi All, First some background. Purchased my 06 last year from an original owner who had installed from what I was told, a Stage 7 kit and a 4-1 Kerker. I was never really satisfied with how the bike ran so I dropped it off to be serviced. The shop told me the slides had been drilled and needed...

I have a set of Stage 7 carbs here. I would like to rebuild them for racing purposes. Which typical rebuild parts will I need, and what will I need for a proper selection of jets? Thanks in advance!!

Look I know there is hundreds of thread about this topic but I have seen some people's set up include dyno 7 parts and morleys kit parts so I want to know what one is the best and easiest to fit !!! and what power differences are there !!!

I am getting mixed answers to this question, can anyone here give their view :bang head: Stage 7 with Pods what do you do with the float bowl vent lines??? Some say remove the hoses from the carbs. some say you need to keep them connected to the carbs and allow the hoses to lay in the...

What does the little washer on the needle that goes between the E-clip and big washer do in a stage 7 kit? Does it REALLY need to go there?=) http://www.dynojet.com/pdf/4716.pdf

125 HP 118 Nm good enough for me :th_signs42:

I have a stage 7. I've always synced the carbs with vboost off. Can you sync them with vboost on?:ummm: Thanks my VMAX brothers.

I finally got Mr Max for the very first time since getting him 4 months ago. The bike came with a Stage 7 kit installed and full UFO exhaust. I sold the UFO exhaust because we have strict noise laws here. So the current setup is Stage 7 and OEM exhaust. The bike starts and idles fine, but...

Well guys I am waiting on carb parts to do a rebuild here. Just curious if anybody has any experience with jetting on a big bore. I am running high comp pistons in a 1428 chain drive but everything else on the top end is stock other than some mild head porting. It will have a marks 4 into 1...

I have Dynojet stage 1 main jets,needles,shims for sale. Make me a offer. Just throwing it out here maybe someone will want them .

Ok so i ordered my Stage 7 kit yesterday and I have these Pod Filters that are new and have had a few months was gona buy the K&N pod filters but thinking of using these and putting the 3 inch velocity stacks under them. I know I will need to put 2 holes in them for the stage 7 breather tube but...

Are the stage 7 shorter noticeably? Or are they the same length but weaker? Thanks Todd

Curious as I pulled my slides out today and noticed they where drilled. The needles are fat and non adjustable. So I am assuming those are stock. My stage 7 needles are thin and adjustable. I am not sure what is in my carbs. But my Stage 7 carbs have 190 DJ jets for the mains and...

edit

Ok...I've searched through loads of the pages (53 on carbies alone :ummm:) Can someone explain in layman's terms... Benefit of removing V-boost ?... I thought this was the best thing about them...turbo like kick at 5000rpm ? What is Stage 7 ?... I thought there was only stages 1 + 3...

Ok Dynojet guys, chime in. New to VMax, and mine is a stock '97 with new Supertrapp slip on's with 6 discs a side. Took the bike in for a 8K service, sync and tune. The verdict from the mechanic is that it still wants more fuel. It wanted to stumble when warm, when I pulled out of a stop. I ran...

I currently have a Kerker 4 into 1 system with a K&N filter. I am looking to go to UFO Dragster pipes with a full Stage 7 kit. Can anyone tell me what kind of power gains I can expect and what the pros and cons would be to go to this setup. I believe the UFO setup would be quite a bit louder...

Is anyone trying or wanting to put a duel stage shift light on a vmax. Im working with raptor on puting one on my bike. I think it going to work great. But its $140.00 I still need to talk with raptor and see what he come up with and than run it by Damon and see what he thinks.

Any of you ever have to clean the plastic canister (puke tank). Would it be possible for it to clog ? Bike runs fine just doin some winter pm.