What did you do to your Vmax today? Part 2

[johnpclynch]

Top cover done, before and after

 

[Blacksun71]

Changed oil and filter and replaced one of the pilot jet screws that was missing a tip. Don't know how the PO has managed to brake it. I found it out when I was executing shotgun to my carbs. I think the broken tip is the main reason why adjusting the pilot screw in that particular carb didn't cause any response.

 

[timscues]

pulled left side covers and removed flywheel to replace and starter clutch, replacing all copper washers on clutch slave while its apart, then fresh oil and filter

 

[jwood]

Installed a break light flash module... CAN YOU SEE ME NOW!

https://www.youtube.com/watch?v=xmRWE5_ODMA&feature=youtube_gdata_player

Sent by the Verizon 4G Data Network

 

[Redbone]

Installed a break light flash module... CAN YOU SEE ME NOW!

https://www.youtube.com/watch?v=xmRWE5_ODMA&feature=youtube_gdata_player

Sent by the Verizon 4G Data Network

BD, here is a Vmax with the flashing brake lights mounted in the reflector location:
http://www.youtube.com/watch?v=F5feH0jnscw

Here is my old setup with the flashing LED still on the plate cover (brake on):


Here is what it looks like now(all three mounted on the MM light mount, flashing in the middle):
Closeup


Rear 3/4


I'll get you a video but it will be indoors. I am still going to redo this in aluminum, but not this year.

 

[dannymax]

BD, here is a Vmax with the flashing brake lights mounted in the reflector location:
http://www.youtube.com/watch?v=F5feH0jnscw

Same exact set up I had on '99 & Sallymax BB, but they didn't flash at the same time like these....:ummm:

 

[dannymax]

I stand corrected....'99 had only one Night Rider light and a Lankee conversion....Sallymax had the two lights.

 

[Miles Long]

BD, here is a Vmax with the flashing brake lights mounted in the reflector location:
http://www.youtube.com/watch?v=F5feH0jnscw

Funny, I remember seeing that red bike around somewhere.....
Oh well, for anyone using the Signal Dynamics Back OFF-XP module (sold by Custom Dynamics), don't forget about the optional circuit that's included, the Motorcycle Emergency Flasher or Automobile Back-Up Flasher.
I've set up mine to flash small LED light bars at the stem and stern of the bike, switched at the dash panel, and hooked direct to the battery.
The idea was to replace the "park" function of the ignition switch. Much less current draw, and a steady flash function for better visibility.
Cheers!

 

[jagco1]

Here's a youtube video of the light I install around 8/2012.
It stays on as a flowing motion, and comes to a bright red light when I hit the brakes.


http://www.youtube.com/watch?v=CNEalaOvIfI

 

[jagco1]

I install new chrome master cylinder covers. I pick up off of ebay.

Price 9.95 plus 6.90 ship..


http://www.ebay.com/itm/1985-2007-Y...s=Model:Vmax+1200&vxp=mtr&hash=item4d19b2c91b

 

[marsmax85]

Received and installed my new bug shield (boulevard) for my 09'

 

[jagco1]

Received and installed my new bug shield (boulevard) for my 09'

nice bike. gut to keep the bugs off.

 

[MaxMidnight]

Carbuncle removal

My ISR master cylinders don't have provision for the brake light and clutch interlock micro-switches.
I had fitted in-line hydraulic switches.

Yep, I agree, they are not in keeping with wot any discerning gentleman would want on his handlebars.

I've now changed them for a pair of 90° switches.
Clutch has gone down by the master cylinder

...and the brake switch onto the splitter. Both neatly out of sight.

I now feel that I will be able to go out in public on my Max without risking the sniggers and sideways looks that I have endured in the past.

PS Any suggestion that I am paranoiac will be strongly refuted...I know that's what you will be thinking.. DOOH!

 

[vmax2extreme]

I posted this a few years ago here:

If you like the idea of the Back Off brake light module, then you'll love this one I have found for a fraction of the price:

http://www.bigrigchromeshop.com/Merc.../LITWH/UP90655

It does the same as the Back Off module and is fully adjustable. I have been using this on my '05 vmax for the past few years without any problems.
__________________

BD, here is a Vmax with the flashing brake lights mounted in the reflector location:
http://www.youtube.com/watch?v=F5feH0jnscw

Funny, I remember seeing that red bike around somewhere.....
Oh well, for anyone using the Signal Dynamics Back OFF-XP module (sold by Custom Dynamics), don't forget about the optional circuit that's included, the Motorcycle Emergency Flasher or Automobile Back-Up Flasher.
I've set up mine to flash small LED light bars at the stem and stern of the bike, switched at the dash panel, and hooked direct to the battery.
The idea was to replace the "park" function of the ignition switch. Much less current draw, and a steady flash function for better visibility.
Cheers!

 

[dannymax]

PS Any suggestion that I am paranoiac will be strongly refuted...I know that's what you will be thinking.. DOOH!

I'm sure the sniggers and sideways looks were nearly unendurable Steve! :rofl_200::rofl_200::rofl_200:

Very nice work, as always! :worthy:

 

[Miles Long]

I posted this a few years ago here:

If you like the idea of the Back Off brake light module, then you'll love this one I have found for a fraction of the price:

http://www.bigrigchromeshop.com/Merc.../LITWH/UP90655

It does the same as the Back Off module and is fully adjustable. I have been using this on my '05 vmax for the past few years without any problems.

Thanks, Mike.
I find the truck supply stores very reasonably priced, and with a great selection of products, when shopping for lighting, electrical supplies, hydraulic hoses and fittings, etc.
On this site, check out the array of headlight bulbs, many 5 3/4", some with LED accent lighting.
Also the wide array of LED auxiliary lights, and for those that would "dare to be different" - double-faced LED turn signals, that look to be doable on our bikes. Now that would make a bike visible!
Cheers!

 

[cmw2212]

Got some parts in this week. Waiting on a few more should be here today or tomorrow.

4 pole starter, 07 rectifier, starter solenoid, cbr integrated tail, ss brake lines front and rear, ss clutch line, brake pads front and rear and Clymer manual. Corbin seat should be here Monday.

Have a few other things coming from overseas, should be here next week.

Knee protectors, grips, res covers.

All in all I have some stuff to keep me busy this weekend.

 

[Traumahawk]

Finally mounted my 18 inch RC rim. I put a 180/55-18 Avon tire on it. To get it on I had to deflate the tire, use WD 40 and then finally drop the bike onto the tire.

I dont have any cans on the bike, because also putting a kerker 4-1 on the bike sometime this weekend.

It looks killer.

 

[CrackerRican]

Finally mounted my 18 inch RC rim. I put a 180/55-18 Avon tire on it. To get it on I had to deflate the tire, use WD 40 and then finally drop the bike onto the tire.

I dont have any cans on the bike, because also putting a kerker 4-1 on the bike sometime this weekend.

It looks killer.

Looking good Eric, your gonna love the ride. Is that the cobra or venum avon

 

[Traumahawk]

Looking good Eric, your gonna love the ride. Is that the cobra or venum avon

Its the Venom...http://www.amazon.com/gp/product/B005J6OI6M/ref=oh_details_o00_s00_i01?ie=UTF8&psc=1

And I have the Avon storm 2 Ultra up front...http://www.amazon.com/gp/product/B005J6OSTY/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1

If I remember right, I think you have the same ones.