size

Anyone know the bolt thread size for the holes in the flywheel? The unused ones so I can attach my puller. Russ

Anyone know the size of the pilot jet screw? I need to clean out some threads and don't have a clue what size tap I need to buy to re-thread the pilot jet screw hole. Thanks, Bill USN Retired

Does anyone know the size of the threads on the pilot jet screw? I had to "easy out" one on a bike I bought and the threads seem to be buggered up a little as the replacement needle jet does not screw in as far as it should. I would like to buy a tap and clean the threads out but I am not sure...

I just found a holeshot full exhaust cheap, but one of the cans is half crushed. I was wondering what size the outlet is on these things. I plan on a set of supertrap universal aluminum racing mufflers (http://www.supertrapp.com/product_sections/cat.asp?CatID=34), but don't know what size to...

Had a break down on the thruway (90) with the company lowboy. Electronic fuel shut off solenoid went bad. Had to get towed. The lowboy is 66 ft long. I was real interested to see the wrecker and how they would tow this thing. It happened around 11 at night so I couldn't really get any pics. The...

Does anybody know what size socket or hex fits the street pro or quadzilla, was going to repack the cans but nothing I have fits?

I was wondering if anybody knew what is the widest tire I can put on a factory 1994 Vmax rear rim without changing anything? Right now I have a factory 1580/90B15M/C 74. Thanks.

I have to repair a rearset and I want to change the thread size. I thought the chinese pegs I had would be 8mm, but they aren't metric. So, I want to make them suit Kuryakin pegs. What size thread do Kuryakin pegs have? :biglaugh:

For anyone looking at a 17" rear but concerned about the gearing changes I found this.... http://www.dunloptyres.com.au/tyres/motorcycle-tyres.dot Lists the diameters of all types....e.g......a 190 60 17 is 664mm, a 190 55 17 is 644 (stock 150 90 15 is 650mm)

Hello folks, and Happy New Year! I've just installed Mark's stainless 4-2, 2" exhaust and the bike started running lean / lacked torque. Then installed Morley's Jet Kit with needles on 4th clip, Mains 160 (2300-2500 ft elev, 47 degrees outside) and I suspect it's running too rich. The...

Hi guys It's time for my 89' to get its first oil change (by me), so I picked up an oil filter from the local Yam dealer, but he didn't have have the O-ring in stock. What size is that bloody thing? same as the filter 101mm?? and thickness? and is it round section?? Sorry if it's been posted...

http://www.mtsac.edu/~cliff/storage/gs/Motorcycle_Rim_Width_Tire_Size_Chart.pdf May take a bit of time to load. Only two pages but seemed to take a bit of time, longer than I would expect.

Can anyone tell me the bolt size that connects the shift linkage to the trans as mine is missing. :ummm: It is the one that squeezes the linkage to the shift shaft on the trans. Don't know how else to describe it.

I have a worn crank bearing that I want to replace, how do you know what part to order?? Luckily this one had some green left on one side so I knew it was a size 4 It's also easy to calculate from the markings and stamps as follows Take the frame markings (on one of the front bosses) and...

Hey Guys, Im looking for feed back from current( or former) MAXGASSER owners:eusa_dance:,what Im looking for is your size( height and weight) and how the MAXGASSER works for you. The reason Im looking for this info is for Potential Customers to see the range of customers size and how well...

Hi, Seen allot of questions about crank, rod bearing size and is wondering what size(in mm) is those different color codes. I'm doing a rebuild of my Vmax engine to support turbo :) Anyone that know? Regards marntzen

What is the size of the battery case? I want to know if an Odyssey batterie can match with it..

I was wondering what people thought was the best tires to put on stock rims for the best handling and also what sizes for front and rear? Can you get a different size for the rear that might work better?:ummm:

I have an OEM backrest that I need to tap out two of the bolts and helicoil them back to size. Does anyone know what the size of the stock bolt that holds the upper backrest frame to the bottom mounting frame? Is it M6 x 1.00? Thanks in advance,

Anyone know what size bolts I need to pull the flywheel ?