size

I am runnig a set of cobra slip-ons currently on my bike however I bought a 4-1 holeshot exhaust recently especially since a lot of people on here told me full exhaust will make a much bigger difference. I ordered a set of 147.5 jets from Sean for the cobra slip-ons (that was before I...

I bought a Russell clutch line and it is made to go directly to the slave cylinder. I want it to connect at the rigid pipe like the stock one does. Does anyone know what type/size fitting I need to put on the line I have. I'm hoping someone local can cut off the banjo fitting that is on the line...

Does anyone know what the size of the small orifice is in the brake & clutch master cylinders? If I could get a size for it, I will look into buying a quantity of the drill bit needed to clean this small hole out and make them available. Should be around a $1 apiece in bulk. I don't have a set...

Does anyone know the socket size of the rear axle nut? It's the one without the cotter pin if that makes a difference. Thanks.

What is the stock rear rim size on an 85 VMax? I have a J 15xMT3.50 DOT and need to know if it is stock. Gary

Very useful when considering different tire sizes or setting a digital speed that requires inputting tire circumference. http://www.discounttireshopper.com/calculator.htm

hey i can't find it quick, does anyone know offhand what size jam nuts we need to hold the damper rod on the 85-92 forks? i may not be able to use the impact while the forks are in the bike trick, or it might be modified and just want that option readily available. its just a what, maybe 24"...

I have the forks apart for some paint work on the bottoms. What size PVC are you people using to get the upper bushings and oil seals back in? Where did you get it? Looked at local hardware (home center), 1.5" too small, 2.0" too large. Do they make 1.75"? I would be greatful for any info...

Anybody know what the machine screw size is for the little set screw that ties the choke arm linkage to the carb. I have noticed that since I have had the bike, it drags 1 cylinder a bit on a cold start, running with the choke. I just figured out why, the left front cylinder has no set screw...

On the rear cylinder exhaust, does anyone know the bolt size for the clamps that keep the exhaust tight? Mine are missing for some reason. Clamps are there, but the bolts are gone. Strange!

I have order a converted rear wheel from Kosman (180 X 17"). Was wondering on what size aspect ratio to run? 180/55/17? 180/60/17? Also what manufacture should i go with? Looking for medium ride life with good handling.

Difference in size of 85 to 86 front header pipes Does anyone know if the front stock header pipes off a 85 gen 1 will fit an 86 gen 1 vmax without any mods to stock exhaust system.

I dont have my valves here in front of me and I need to order a valve guide pilot to cut my valve seats I think they are 5.5mm? or if any one happens to have a guide that they could lend out for a neway cutter with a .375 top. thanks

What is the best website to buy tires? I have the stock front wheel and a custom 18" rear wheel. I was thinking of geting 110/80/18 for the front and 180/55/18 rear (radials). what is the best set of tires in this size and where should i get them from? Also is it safe to use 120/70/18 on the...

Does anybody have a Vmax carb apart ? I'm tying to find the head diameter of the main fuel jet. It's either 6mm or 8mm - I'm thinking it's probably 8. I'm looking at jets on this website : http://www.pjmotorsports.com/mikuni-jets.html The paj2 is jet part number N102/221 with the 6mm...

Have 07 vmax with a 17mm oil drain plug. I would like to replace stock plug with one that has a magnet. Does anybody know the plug size and tread type:ummm:

Hi, We dismantled the fork today and unfortunately the intiminators won't drop in (41mm). The thread on top is preventing it. :bang head: The part of the valve going on top of the damper rod has a 40mm diameter and seems larger than the damper rod. It seems I got the 43mm version even if...

Hi all: Any of you know where I might be able to buy a custom-length rear brake stay bar? (This is what Yamaha calls the "REAR BRAKE TENSION BAR" part number 36Y-25371-00-00.) I bought an excellent 8" extended swingarm from Sean Morley for my 1986 FZX700, and I want to see if I can mount...

What is the largest tire size that will work on my 1995 with stock rear rim? Thanks, Randy in Phoenix

i've been wanting to change my plugs, does anyone know the size socket i need? the plugs i have are ngk-dpr8ea-9 thanks